644686

Greenworks 2600107 - 80V Pro Manual

18
Zoom out
Zoom in
Previous page
1/292
Next page
EN - 7
E.
F. Handle pivot closure
G. Central handle
H. Ignition key
I. Exhaust chute
J.
K. Auger
L. Auger compartment
M. Wheel
N. Lower blade
O.
Transport handle
P.
Battery compartment
Q.
Battery charger (supplied separately)
Battery (supplied separately)
4. ASSEMBLY
For storage and transport purposes, some
components of the machine are not installed
in the factory and have to be assembled after
unpacking. Follow the instructions below.
4.1 ASSEMBLY COMPONENTS
The packaging holds the components needed
for assembly
4 ) listed in the following table:
Component Fig. N.
Snow thrower 4 1
Discharge chute
adjustment handle
4.A, 4.A1,
4.A2
1
Handle 4.B 1
Handle
4.C 1
Spacers and screws for
securing the handle in place
4.D, 4.E 2
Spacers and screws for
securing the handle in place
4.F, 4.G 4
Ignition key 4.H 1
1
4.J
1
Instructions -
4.2 UNPACKING
1. Cautiously open the packaging, paying
attention not to lose components.
2. Consult the documentation in the box,
including these instructions.
3. Remove all the unassembled parts from the
box.
4. Lift the snow thrower from the box.
5. Dispose of the box and packaging in
compliance with local regulations.
4.3 HANDLE ASSEMBLY
1. Assemble the central part of the handle
4.C) on the snow thrower (lower part of
handle), fastening it with screws
4.D, 4.E)
on both sides.
2. Position the upper handle
4.B) on the
central one and fasten it with the
screws and fastenings
4.G, 4.F).
3. Fasten the electrical cable in place with the
cable gland 4.I).
4.4 DISCHARGE CHUTE ADJUSTMENT
HANDLE ASSEMBLY
1. Assemble the handle
5.A1) using the
extension shaft 5.A), fastening it
in place with a spring pin
5.A2). Ensure
the holes on the shaft and the joint are aligned.
2. Insert the spring pin in the hole and fasten.
3. Pass the handle obtained in the
lower
handle support
5.B).
4. Insert the end of the handle in the
coupling hole on the chute, keeping it straight
and with the grip upwards
5.C).
5. Check the discharge chute by turning it
entirely in both directions. The chute must
freely rotate
9 ).
4.5 DEFLECTOR ASSEMBLY
1. Insert the
on the discharge duct in
the upright position
6.A).
2. Fit the tabs on both sides in the rotation
eyelets
6.B).
3. Push until the pins
into the holes
with a click.
5. CONTROLS
5.1 IGNITION KEY
Used to start and stop the motor. The
ignition key has two positions
8.H):
1. Key removed - OFF - the motor stops and
cannot be restarted.
2. Key inserted - ON - the motor can start and
run.
5.2 STARTER LEVER
Used to start and stop the motor.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Greenworks 2600107 - 80V Pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Greenworks 2600107 - 80V Pro in the language / languages: All languages as an attachment in your email.

The manual is 5,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info