637243
19
Zoom out
Zoom in
Previous page
1/30
Next page
11 94001 GM-Racing XG-6i Race Spec Instructions
English
14. TH HOLD
This function allows the Throttle Servo to be set to a percentage of the total travel
range. This is an alternative to using the motors choke when starting up the model. Throttle
hold can be performed by pressing the switch to stop the engine. It can be perfor-
med for accident braking. When pressing the switch, throttle trigger doesn‘t work until
the switch is pressed again.
1. Press “ENTER” to see FUNCTION MENU
2. Use the +/- Keys to select the TH HOLD function and press ENTER.
3. Use the +/- Key to change the value.
4
. Press EXIT twice to save and return to FUNCTION MENU, press EXIT again
to return to the Main Screen.
TERMS: VALUE -- Throttle hold position. Range: -120% to +120%.
13. MIXER (MIX)
This function allow custom to apply mixing between the steering, throttle, and channel
3 channels.There are main channel and sub-channel in the MIX selection. The servo
travel value of the sub channel is changed along with the change of the main channel
according to the setting rate.
1.
Press “ENTER” to see FUNCTION MENU
2. Use the +/- Keys to select the BR_MIX function and press ENTER.
3. Press ENTER to select a item.
4. Firstly main channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L and R se-
parately correspond to the rate of Left and Right servos of the main channel mix
5. Secondly sub channel setting. Select channel No. (ST, TH, AUX) by “+” or “-“. L and R
separately correspond to the rate of Left and Right servos selected in the sub
channel.
6. Third Press ENTER to select EN item. Use +/- to select “ON” to enable the
function, and “OFF” to disable the function.
7. Press EXIT twice to save and return to FUNCTION MENU, press EXIT again to
return to the Main Screen.
Exemple:
ST L 50% R 30% If throttle servo is 60% on the right and rudder servo is 50% on the right,
and then after setting, throttle servo is: 50*30%+60%*50%=45%. Thrott-
le servo will act along with the action of STEERING servo.
TH L 20% R 50%
EN „ON“
94001 GM-Racing XG-6i Race Spec Instructions 08
English
ENTER MODEL NAMES:
1. Press “+” or “-”to choose “EDT”.
2. Press “ENTER” to enter rename mode ,Press “+” or “-”to choose “0.1.2....I”
3. Press “ENTER” on the display to save your modi ed and return to the MODEL Screen..
4. Press “EXIT”to save your setting and leave EDT interface, and back to the function
menu interface.
COPY ONE MEMORY TO ANOTHER:
1. Press “+” or “-”to choose “CPY”.
2. Press “ENTER” to enter copy mode ,Press “+” or “-”to choose “Mod01....Mod15”
3. Press “ENTER”to save your setting and Press “EXIT”leave CPY interface, and
back to the function menu interface.
8. MODELL MEMORY (MODEL)
Press “ENTER” in the power on interface, and enter function menu interface. Press
“+” or “-“ to choose MDL, and press “ENTER” to enter MODEL adjusting interface.
1. Press “ENTER” to choose “mod00”.(SEL)
2. Press “+” or “-”to choose “mod00~mod15”
3. Press “EXIT”to save your setting and leave SEL interface, and back to the function
menu interface.
94001-eng.indd Druckbogen 9 von 10 - Seiten (12, 9)94001-eng.indd Druckbogen 9 von 10 - Seiten (12, 9) 19.01.2009 08:02:4919.01.2009 08:02:49
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner XG-6i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner XG-6i in the language / languages: English, German, French as an attachment in your email.

The manual is 2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info