747911
31
Zoom out
Zoom in
Previous page
1/48
Next page
Page 31 of 48 S1047.mz-16-V1.0-EN
receiver). Touching the check mark in the boom right conrms the
selecon.
7. If necessary, proceed idencally with other receiver connecons.
8. By tapping on the symbol pulse , you can change to level and
back to pulse again.
When the symbol pulse is selected, servo pulses are output to the
corresponding channel output.
When the symbol level is selected, the output of the corresponding
channel is switched to high or low.
N
otes
Switching to level allows the direct connecon of transistors or
LEDs to the receiver output via a series resistor.
For Graupner receivers GR-12 (#33506), GR-16 (#33508), GR-24
(#33512), GR-32 (#33516) and GR-24 PRO (#33583) as well as
GR-16L (#S1021), GR-24L (#S1022) and GR-32L (#S1023) series
resistors are already installed and LEDs can be connected directly
between the orange servo pulse wire and the brown or black “-”
wire.
9. Touching “OK” completes the process. Touching “Reset” resets the
receiver to the default sengs.
In both cases, the display will close, and you will return to the “RF Set” menu.
Assign Digital Switches to Widgets
1. Switch to the submenu “Digital Switch”.
2. Tap on the rst “Acticon to acvate the Digital Switch and select
the desired mode (On/O, Pulse or Flash).
3. Connect for example a servo to the channel you designated as Digital
Switch.
4. Go to the Home page and select an empty deck or available block
and bring up the Widget Editor.
5. Select the “Digital Switch” widget and tap on DS1 which is the digital
channel we assigned in the previous step.
6. Test the opera
on by tapping on the buon. You can change its
behavior in the “Digital Switch” submenu.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MZ-16 HoTT - S1047 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MZ-16 HoTT - S1047 in the language / languages: English as an attachment in your email.

The manual is 25,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MZ-16 HoTT - S1047

Graupner MZ-16 HoTT - S1047 User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info