747911
28
Zoom out
Zoom in
Previous page
1/48
Next page
Page 28 of 48 S1047.mz-16-V1.0-EN
The transmier does not automacally enable each bound receiver as part
of the channel count. This must be done manually in the RF Set menu. For
example, if RX1 is an 8-channel receiver it will serve only channels 1 to 8 on
that receiver. When a second 8-channel receiver is bound on RX2 it will
serve the exact same channels 1 to 8 on its receiver outputs providing you
with two receivers that mirror each other’s channel outputs.
To designate a receiver as a connuaon of the channel
count of the
previous bound receiver you will need to reset the channel mapping in the
RF Set menu.
N
ote
You must verify that you are using the latest rmware on your receiver to
enable channel mapping or digital switches.
Channel Mapping
1. Go the RF Set menu and bind two receivers to bind posions Rx1 and
Rx2.
2. Verify in the Rx column the channel count of the receiver and its
rmware version. For example, an 8-channel receiver will show as R8
and below it will show in small print the rmware version for example
7.06.0.
3. Tap on the Rx column of the second receiver to highlight it. The
background will turn to blue and tap again to bring the receiver
channel map dialog.
4. Tap
on reset to renumber the channels for that receiver. The servo
map dialog will now show that the rst channel output on the
receiver is mapped to channel 9 and when scrolling the channel list
down you will noce that receiver output 8 is mapped to channel 16.
You can undo this operaon by tapping again on reset which restores
the channel numbering.
5. Tapping Ok will acvate the new channel mapping. It can be tested
by assigning a control in the Control Set menu for example to chann
el
16 and plugging in a servo on channel 8 of Rx2 to verify channel
operaon.
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MZ-16 HoTT - S1047 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MZ-16 HoTT - S1047 in the language / languages: English as an attachment in your email.

The manual is 25,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MZ-16 HoTT - S1047

Graupner MZ-16 HoTT - S1047 User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info