30127
21
Zoom out
Zoom in
Previous page
1/48
Next page
highlighted.
5. Move the appropriate control stick (lever, switch,
etc.) to the right or left of center to the direction of
travel you want to adjust. An arrow to the left of the
travel adjust value will reflect the current position to
be adjusted.
6. After the control stick or switch is placed in the
direction of travel to be adjusted, press the (+) or
(-) key until the proper amount of servo travel is
shown on the LCD. Press the (+) key to increase the
amount of servo travel. Press the (-) key to decrease
the amount of servo travel.
7. Follow the same procedure for the remaining chan-
nels.
8. Access the SUB TRIM function by pressing the
Down key.
9. Access the ELE F MX function by pressing the
Up key.
10. Exit the TRAVEL ADJ function by pressing the
Down and Select keys simultaneously.
Elevator to flap mixing
When this system is active and a value of flaps is input,
the flaps will be deflected each time the elevator stick is
used. The actual flap movement is adjustable for both
up and down elevator. A switch can be assigned to turn
the elevator to flap mixing on or off.
MIXING VALUE (+/- 125%)
Elevator Operating Direction
E-DN: Down side
E-UP: Up side
Mixing SW Selection
SW Display
ALWAYS ON: Always Mixing In
RIGHT FWD: Gear SW Forward
side On
RIGHT REA: Gear SW Rear
sideOn
LEFT FWD: FLAP SW Forward sideOn
LEFT REA: FLAP SW Rear sideOn
AILE D/R: AILE D/R SW Position 1On
ELEV D/R: ELEV D/R SW Position 1On
Go to Ail
Rud Mix menu
Go to Travel
Adjust menu
Change selection
Change value/Select
switch
Reset selection to
Default (adjust to 0%
or ALWAYS ON)
Accessing the Elevator to Flap Function
1. Place the transmitter power switch on the ON positi-
on.
2. Access the Function mode. To do so, press the
Down and Select keys simultaneously.
3. Move the elevator stick in the direction you want to
mix with flaps.
Note: The position indicator will reflect this change by
highlighting the up or down arrow.
4. Press the (+) or (-) key to increase or decrease the
amount of flaps to be mixed. If you want to reverse
the flap travel, press the Clear key, bringing the
mixing value to the factory default (0%), and increa-
se the value using the opposite key (+) or (-) from
the key originally selected.
5. Once you have adjusted the first mixing position (up
or down), place the elevator stick in the opposite
direction and follow Step 5 above to adjust the
second elevator mixing value.
6. Access the switch position by pressing the Select
key. Use the (+) or (-) keys to select from the one of
six switches, or from always on.
7. Access the TRAVEL ADJ function by pressing the
Up key.
8. Access the AIL RUD MIX Mixing function by pres-
sing the Up key.
9. Exit the ELE F MX function by pressing the
Down
and Channel keys simultaneously.
Aileron to rudder mixing
This form of mixing is designed so that when input to the
aileron stick is given, the rudder servo will also move,
eliminating the need to coordinate these controls manu-
ally. When adjusting, if an opposite mixing direction of
the rudder servo is required, simply press the (+) or (-)
keys to change the mixing value from a (+) or (-). This
will reverse the mixing direction of the rudder from its
original direction. The switch used to activate this mix
can also be selected as explained below. The factory
default is a value of 0%
Function mode AIRPLANE
Elevator to flap mixing; Aileron to rudder mixing
MIXING VALUE (+/- 125%)
Mixing SW Selection
SW Display
ALWAYS ON: Always Mixing In
RIGHT FWD: Gear SW Forward side On
RIGHT REA: Gear SW Rear sideOn
LEFT FWD: FLAP SW Rear sideOn
LEFT REA: FLAP SW Rear sideOn
AILE D/R: AILE D/R SW Position 1On
ELEV D/R: ELEV D/R SW Position 1On
Function mode AIRPLANE 21
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English, German - 144 pages

Graupner MX12 User Manual - Dutch - 47 pages

Graupner MX12 User Manual - French - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info