30127
20
Zoom out
Zoom in
Previous page
1/48
Next page
20 Function mode AIRPLANE
3. Press either the Up or Down key until TRAVEL
ADJ appears in the upper portion of the LCD.
4. Using your transmitter`s control sticks, switches and
potentiometers, move the control surfaces of your
aircraft. Note the travel direction of each of the
corresponding control surfaces.
5. After you have determined which channel(s) need to
have the throw directions reversed, use the Select
key to call up the appropriate channel.
6. Press either the (+) or (-) keys to change the travel
directions of the servo. Pressing the Clear key re-
turns the travel direction to Normal.
7. You can observe the change in the travel direction
by moving the appropriate control at this time.
8. Access the D/R & EXP function by pressing the
Down key.
9. Access the SUB TRIM function by pressing the Up
key.
10. Exit the SERVO REVERSING function by pressing
the Down and Select keys simultaneously.
Sub Trim
Function mode AIRPLANE
Sub Trim; Travel Adjust
Travel Value
(0~150%)
The Sub Trim Adjustment function allows you to electro-
nically fine-tune the centering of your servos. Individual-
ly adjustable for all six channels with a range of +/-
125% (+/- 30 degrees servo travel).
The sub trim function provides precise servo arm neutral
positioning if rotating the servo arm will not allow the
desired servo arm position.
Go to Travel Adjust
menu
Go to reversing SW
menu
Select channel
Change value
Reset selection to
default (Adjust to 0)
Accessing the Sub Trim Function
1. Place the transmitter power switch in the ON positi-
on.
2. To Access the Function mode, press the Down and
Select keys simultaneously.
3. Press either the Up or Down key until SUB TRIM
appears in the upper middle portion of the LCD.
4. Press the Select key until the desired channel
appears.
5. Press the (+) or (-) key to establish the desired
amount and direction of Sub Trim.
Caution: Do not use excessive Sub Trim adjustments
since it is possible to overrun your servo`s
maximum Sub Trim. Remember that it is a trim
convenience function.
It is not intended to take the place of the
proper mechanical trim adjustments that are
necessary on any RC model.
6. Access the REVERSING SW function by pressing
the Down key.
7. Access the TRAVEL ADJ function by pressing the
Down key.
8. Exit the SUB TRIM function by pressing the Down
and Select keys simultaneously.
Travel Adjust
Channel being programmed
THRO 1: THROTTLE
AIL 2: AILERON
ELE 3: ELEVATOR
RUD 4: RUDDER
GEA 5: GEAR
FLA 6: FLAP
Travel Value
(0~150%)
Channel being programmed
THRO 1: THROTTLE
AIL 2: AILERON
ELE 3: ELEVATOR
RUD 4: RUDDER
GEA 5: GEAR
FLA 6: FLAP
The purpose of Travel Adjust is to offer you precise
servo control deflection in either direction of servo
operation. The mx-12 offers travel adjust for all six
channels. The Travel Adjust range is from 0-150% (0 de-
grees to 60 degrees) from neutral, or center, and it can
be adjusted for each direction inividually. The factory
default (Data Reset) value is 100% for each direction of
servo travel.
Go to Ele F MX menu
Go to Sub Trim menu
Select channel to
Adjust
Change value
Reset value to
Normal (Adjust to
100%)
Accessing the Travel Adjust Function
1. Place the transmitter power switch in the ON positi-
on.
2. Access the Function mode by pressing the Down
and Select keys simultaneously.
3. Press either the Up or Down key until TRAVEL
ADJ appears in the upper portion of the LCD.
4. Press the Select key until the desired channel is
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English, German - 144 pages

Graupner MX12 User Manual - Dutch - 47 pages

Graupner MX12 User Manual - French - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info