Manual Graupner MX12 (page 90 of 144) (English, German, French)

30127

Zoom out

Zoom in

1/144

System Mode

sing function to reverse the travel direction.

Note: Each servo‘s direction is adjusted individually

through the Servo Reversing function. For more

information, refer to the Servo Reversing sec-

tion in this manual.

7. Once the servos direction has been set, adjust their

travel direction, travel volume, dual-rates, sub-trim

and aileron differential.

Note: The applicable channel‘s left or right, up or

down travel adjustments can be made individu-

ally. Refer to the Travel Adjust section in this

manual for more information.

8. Relative to the note above, each servo‘s travel

volume is automatically reduced to 75% of the

operating range. This is to ensure that the servo

does not operate beyond its capabilities. Failure to

observe extreme caution when adjusting the value

for the elevon servos may result in damage to the

servos by over traveling.

Note: Fine adjustments of the elevons should be

made in the Dual-Rate function. For more infor-

mation, refer to the Dual-Rate section in this

manual. You can also adjust the neutral point of

your elevon servos individually using the Sub-

Trim function as described in the Sub-Trim

section of this manual. Differential is offered for

the elevon function of your mx-12. For more

information, refer to the Differential Aileron

Mixing section of this manual.

9. Press the Down key to access the SWITCH SEL

function.

10. Press the Up key to access the MODEL SEL func-

tion.

11. To exit the WING TYPE function, press the Down

and Select keys simultaneously.

servos. However, there is not an elevator present.

Instead, an elevator stick input causes the two wing

servos to function in conjunction with one another to

change the pitch movement of the aircraft. Also, when

an aileron control is given the two wing servos move in

opposition to one another to function as ailerons.

Connect left servo to the

aileron port of the receiver

Connect right servo to the

elevator port of the receiver

Accessing and Ultilizing the Elevon Type Selection

1. While the Down and Select keys are pressed,

move the power switch to the ON position to access

the System mode.

2. Press either the Up or Down key until WING TYPE

appears on the LCD.

3. Press the Select key to select the Elevon functions.

4. Press either the (+) or (-) key to turn on the Elevon

Wing Type function.

Note: The Elevon function requires one servo for each

elevon, i.e. a separate servo for each wing half.

5. Plug the left elevon servo to the aileron (AILE) of

your GRAUPNER receiver. Connect the right elevon

servo into the elevator (ELEV) port of your receiver.

6. Check to make sure the servos move in the proper

direction. When an input is given from the elevator

stick, they should move in unison to achieve the

proper up/down elevator command. If your servos do

not move as described above, use the Servo Rever-

direction.

Note: Each servo‘s travel direction is adjusted indivi-

dually through the Servo Reversing function.

Once the servos achieve their proper travel direction,

adjust their travel amount, dual rates, sub-trim and

aileron differential.

Note: The applicable channel‘s left or right travel

adjustment may be made individually by acces-

sing the Travel Adjust function. Refer to the

Travel Adjust section of this manual for more

information. The fine adjustments of your aileron

controls should be made in the Dual-Rate func-

tion. Refer to the Dual-Rate section for informa-

tion on how to do so. You can also adjust the

neutral point of your aileron servos individually

through the use of the Sub-Trim function. Refer

to the Sub-Trim section of this manual for more

information.

6. The flap lever located on the left face of the transmit-

ter controls the aileron movements as flaps. To turn

off flaps go to the Flap System function on page 39

and reduce the flap value to 0%.

Note: Differential is offered for the Flaperon function of

your mx-12. For more information, please refer

to the Differential section of this manual.

7. Press the Down key to access the SWITCH SEL

function.

8. Press the Up key to access the MODEL SEL func-

tion.

9. Exit the WING TYPE function by pressing the

Down and Select keys imultaneously.

Elevon Type Selection

Elevon Wing Mixing is available as an option with your

mx-12. This style of aircraft also employs two wing

42 System Mode

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English, German, French as an attachment in your email.

The manual is 15,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English - 48 pages

Graupner MX12 User Manual - Dutch - 47 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MX12 Manual

Product: