30127

Graupner MX12 Manual

79
Zoom out
Zoom in
Previous page
1/144
Next page
trim lever has no effect on positions 1 or throttle hold.
Note: Making changes to the throttle trim lever does
not change the input values for any of the points
on the throttle curve; it merely makes adjust-
ments to the engine idle speed postition.
Output value
Graphic display
POINT
P-LOW : Full Slow position P-3 : Stick 3/4 position
P-1 : Stick 1/4 position P-HIGH : Full High position
P-MID : Stick Center position * Point position is fixed
Hovering Throttle Lever Settings
The Hovering Throttle lever increases or decrease the
engine output power for the middle three points set for
the middle three points set for the throttle curve. As
shown in the figure below, use of the hovering throttle
lever shifts the curve upward or downward parallel with
the original curve. Therefore, operation of the hovering
throttle knob does not cause any change to the original
settings of the throttle curve.
The throttle trim range will affect the throttle curve as
shown.
The adjustable range of output using the hovering thrott-
le lever is approximately +/- 9%.
Note: The Hovering Throttle has no effect on flight
mode switch position 1.
Throttle Stick
Function mode HELICOPTER
Pitch Curves
Function mode HELICOPTER 31
Hovering Throttle Knob
Operating Range (Parallel)
Output Value
P-HIGHP-MIDP-LOW
Throttle Trim
Operating Range
Pitch Curves
Adjustment of the pitch curve is very similar to the thrott-
le curve adjustment described in the preceding section.
A thorough understanding of the Throttle Curve Section
will make pitch curve adjustment easier to understand.
There are three independent types of pitch curves
available: Normal, Stunt, and Hold. Each pitch curve
contains five adjustable points: LOW 1, MID 3, and
HIGH.
Note: The pitch curve for the Throttle Hold function
can only be set if this system is activated.
Flight Mode SW position
Graphic display
Output position
Stick position
Go to Revolution
Mixing menu
Go to Throttle Curve
menu
Select function to
change
Change Value/Switch
selection
Reset POS value to
0 or Inhibit function
Accessing the Pitch Curve Function
1. Place the transmitter power switch in the ON positi-
on.
2. Press the Down and Select keys simultaneously
to enter the Function mode.
3. Press either the Up and Down key until PITCH
appears in the top of the LCD.
Note: Use NORMAL for hover curses and STUNT for
stunt curves. We will concentrate on the ho-
vering curve during this example.
4. Press the Select key to select the point of the curve
you want to change.
5. Press either the (+) or (-) key to change the value of
the current curve point. The range of each point is
0-100% in 0.5% intervals.
Note: In each curve, the factory setting INH indicates
Inhibited for points 1 and 3. These values are
25% and 75% respectively, if no value changes
are made to any other points. If any of the other
points have been changed while these points
were inhibited, the inhibited points will change
to plot a smooth curve. If you want to keep
this from happening, press the Select key to
display the positions 1 and 3, then press the (+)
or (-) key to activate each point.
6. To set curves for STUNT mode, press the Select to
highlight the NORM function, then press the (+) or
(-) key to select the STUNT function, Repeat Steps 4
and 5 to complete the procedure.
7. To set the curves for the Throttle Hold mode “H“,
… 79 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English, German, French as an attachment in your email.

The manual is 15,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English - 48 pages

Graupner MX12 User Manual - Dutch - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info