Manual Graupner MX12 (page 77 of 144) (English, German, French)

30127

Zoom out

Zoom in

1/144

Ch6 = Pitch

3 servo (120°)

Ch2 = Aileron

Ch2 = Elevator

Ch6 = Pitch

Throttle Cut Switch

This function assigns the Throttle Cut switch to the push

button located on upper right front of the transmitter.

The Throttle Cut function is designed to return the

throttle trim to the lowest position instantly and keep this

position while the button is pressed. This feature is used

to “cut“ or stop the engine without changing the position

of digital throttle trim.

Function mode HELICOPTER

Throttle Cut Switch; Throttle Hold

Function mode HELICOPTER 29

Throttle Cut Operating position

(-32~-128)

Go to Throttle Hold

Go to Travel adjust

Change value

Set function to Inhibit

Accessing the Throttle Cut Function

1. Place the transmitter power switch in the ON positi-

on.

2. Access the Function mode. To do so, press the

Down ans Select keys simultaneously. Press

either the Up or Down key until THRO CUT ap-

pears in the upper portion of the LCD screen.

3. Us the (+) and (-) keys to change the value of the

Throttle cut function.

Note: Pressing the Clear key will Inhibit the Throttle

Cut, turning it off until it has been reactivated.

4. Access the TRAVEL ADJ mixing function by pres-

sing the Down key.

5. Access the THROTTLE HOLD function by pressing

the Up key.

6. Exit the THRO CUT function by pressing the Down

and Select keys simultaneously.

Throttle Hold

The Throttle Hold function is designed to hold the thrott-

le servo in a specific position during an autorotation.

This is very useful for practicing autorotation landings.

The throttle hold switch can be programmed to one of

the four toggle switches. Throttle hold will always be

“On“ in the forward switch position and “Off“ in the rear

position.

Press +/- key Press CLR key during selecting

Go to Throttle Curve

Go to Throttle Cut

Select function to

change

Change value/SW

selection

Reset POS value to 0

or Inhibit function

Throttle Hold Position

(-20~50)

Hold SW Select

Switch

LEFT : THRO HOLD SW Forward SideOn

AILE D/R : AILE D/R: AILE D/R SW Position 1On

ELEV D/R : ELEV D/R Position 1On

RIGHT : FLIGHT MODE SW Forward SideOn

Accessing the Throttle Hold Function

1. Place the transmitter power switch in the ON positi-

on.

2. Press the Down and Select keys simultaneously

to enter the Function mode.

3. Press either the Up or Down key until THROTTLE

HOLD appears across the top of the LCD.

4. The factory setting for the throttle hold is inhibit.

Pressing either the (+) or (-) key will activate Throttle

Hold and display the current throttle hold value.

5. Using the (+) or (-) key, adjust the throttle hold

value to deliver the proper engine idle rpm for your

helicopter. The adjustable range is (-20% -/+ 50%).

Once you establish the proper idle value for your

engine, you can use this value for throttle hold as

well. To shut the engine off for autorotation, a negati-

ve or zero value should be input.

Note: When the throttle hold is activated, and the

switch is on, the indicator on the LCD will

change from Off to On. In addition, the throttle

trim indicator will be inhibited.

6. Access the THROTTLE CURVE function by pres-

sing the Up key.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English, German, French as an attachment in your email.

The manual is 15,11 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English - 48 pages

Graupner MX12 User Manual - Dutch - 47 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MX12 Manual

Product: