467107
173
Zoom out
Zoom in
Previous page
1/200
Next page
173
Programming example - fixed-wing model
MIX1 c1 c1
trv
0%offs
ASYSYM
–100%
–100%
Now move to the “Offs” line: when you do this, the SYM
and ASY fields are replaced by STO and SET. With
the STO button highlighted, move the Ch 1 stick to the
“OFF” position you have selected, and then touch the
central SET button of the right-hand touch-key: the value
to the right of “Offs” now changes from 0% to approx.
+100%, and the graphic display of the mixer curve
displayed on the right also changes accordingly:
MIX1 c1 c1
trv
+100%offs
SETS TO
–100%
–100%
If you now touch the  buttons of the left-hand touch-
key simultaneously to move to the …
“Servo display” menu (page 133),
… you can immediately check the effect of the settings
you have entered so far: with the mixer switched off,
the bar display for Channel 1 follows the movement of
the Ch 1 stick. With the mixer switched on it stops - as
shown - at around -100%.
Once you are confident that the direction of the Ch 1
stick is “correct” as far as the motor is concerned, the
next step is to ensure that you can switch its effect on
the motor on and off, so that you can also control the
braking system. This is carried out in the …
“Free mixers” menu (pages 127 … 132)
typ fro
to
M1
M2
M3
??
??
c1
??
c1
??
2
… where you need to program a free mixer “c1 c1”.
When you have done this, use the arrow button of the
left or right-hand touch-key to move to the column above
the symbol, and assign your selected “change-over
switch” to this mixer; for example SW 2. This is done by
activating the switch assignment by touching the central
SET button of the right-hand touch-key, and moving the
switch from “forward” to “back”, i. e. towards you.
With the mixer switched on, move to the column above
the
symbol using the arrow button of the left or
right-hand touch-key, and then on to the second screen
page by touching the central SET button of the right-
hand touch-key.
At this point you should set an initial SYMmetrical mixer
value of -100%.
“Servo settings” menu (page 92)
S1
S2
S3
r ev cent
+
trav
0%
0%
0%
100%
100%
100%
100%
100%
100%
0%
0%
100%
100%
100%
100%
S4
S5
… and reverse the direction of servo 1.
For safety’s sake you should check this setting now,
before you continue with the programming procedure.
Take the transmitter and model to a location where it
is safe to run the motor. Switch the transmitter on, and
move the Ch 1 stick to the motor “OFF” position, i. e. ei-
ther fully forward or back. Hold your model firmly, or ask
a friend to hold it for you. Check that the propeller is free
to rotate without causing havoc, then connect the flight
battery and switch your model’s receiving system on.
If the motor does NOT run when the stick is in the “for-
ward” or “back” position (as appropriate), then everything
is in order. However, please check the system anyway by
gradually advancing the stick until the motor begins to
run. When you are satisfied, stop the motor, then switch
off the receiving system in the model and finally switch
off the transmitter.
Note:
If the motor does not start, or spins in the wrong direc-
tion, this indicates that there are other problems which
you must correct before you continue with programming.
For example, check the wiring of your motor, and refer
to the operating instructions supplied with your speed
controller.
173


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info