467107
116
Zoom out
Zoom in
Previous page
1/200
Next page
116
Program description: helicopter mixers – model helicopter
Points “1” and “5”, however, CANNOT be disabled.
Note:
The following illustration, and all the other pictures on
this page, show a control curve which we prepared for
illustration purposes only. Please note that the curve
characteristics by no means represent real collective
pitch curves!
input
output
point 3
0%
–50%
–50%
ptch
normal
Typical collective pitch curves for different flight phases:
+100% +100% +100%
100%
100%
100%
Output
Output
Output
2 3 4 51
2 3 4 51
2 3 4 51
Control travel Control travel Control travel
Hover
Aerobatics 3D
ch1 thro (throttle curve)
input
output
point
3
+50%
+50%
+50%
ch1
normal
thro
Helicopter with glow engine or electric motor and
STANDARD SPEED CONTROLLER
This setting only affects the control curve of the throttle
servo or speed controller.
The method of setting up a throttle curve for a model
helicopter fitted with a speed governor or regulator is
discussed later.
The throttle curve can be defined using up to five points,
in a similar way to the collective pitch curve (see previous
page).
In all cases the control curve must be set up in such •
a way that the throttle is fully open, or the speed
controller of an electric helicopter is at full power, at
the end-point of the throttle / collective pitch stick,
(exception: auto-rotation - see page 124).
The hover point is normally located at the centre of •
the stick travel, and the throttle setting should be
adjusted relative to the collective pitch curve in such
a way that the correct system rotational speed is
obtained at this point.
At the minimum position of the throttle / collective •
pitch stick the throttle curve should initially be set up
so that the (glow) motor runs at a distinctly higher
speed compared to the idle setting, with the clutch
reliably engaged.
In all flight phases the motor (glow or electric) is
started and stopped using the throttle limiter (see
below).
If you are used to a different radio control system which
uses two separate flight phases for this - “with idle-up”
and “without idle-up”; therefore incurring the “loss” of
one complete flight phase - please note that the throt-
tle limiter renders this complication superfluous, as the
increased system rotational speed below the hover point
in the mx-16 HoTT program is more flexible, and can
be fine-tuned more accurately, than the “idle-up” system
used with earlier mc radio control systems.
Ensure that the throttle limiter is closed before you start
the glow motor, i. e. the throttle can only be adjusted
within its idle range using the idle trim. Be sure to read
the safety notes on page 122 which refer to this. If the
idle is set too high when you switch the transmitter on,
you will see and hear a clear warning!
stop
STARLET
#02
2:22h
0:00
0:00
5.5V
5.2
HoTT
mal »
M
throttle
too
high !
The following three diagrams show typical 3-point throttle
curves for different flight phases, such as hover, aerobat-
ics and 3-D flying.
116


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info