467107
81
Zoom out
Zoom in
Previous page
1/200
Next page
81
Program description: base settings - fixed-wing model
phase 3
phase 4 landing
speed
–––
6
receiv out
rx bind
R08
range test
99sec
When you start the range-check, the transmitter’s
output power is significantly reduced, and the blue
LED on the aerial base starts to flash. At the same
time the time display on the transmitter screen starts
counting down, and a double beep sounds every five
seconds.
From five seconds before the end of the range-check
you will hear a triple beep every second. When the
99 seconds of the range-check period have elapsed,
the transmitter switches back to full power, and the
blue LED glows constantly once more.
Within this period walk away from the model, moving 6.
the sticks all the while. If at any point within a distance
of about fifty metres you notice a break in the connec-
tion, attempt to reproduce it.
If the model is fitted with a motor, switch it on in order 7.
to check the system’s interference rejection.
Walk further away from the model until you no longer 8.
have full control over it.
At this point wait until the test period has elapsed, with 9.
the model still switched on and ready for use. When
the range-check period is over, the model should re-
spond again to control commands. It this is not 100%
the case, do not use the system. Contact your nearest
Service Centre of Graupner GmbH & Co. KG.
Carry out the range-check before every flight, and 10.
simulate all the servo movements which are likely to
occur in a typical flight. To ensure safe operation of
the model, the range must always be at least fifty me-
tres on the ground.
Caution:
Never initiate a range-check when you are actually
operating a model!
RF transmit
In this menu line you can manually switch the transmit-
ter’s RF transmission on and off again for a specific
model for the current period that the transmitter is
switched on. For example, you might wish to do this to
save power when demonstrating the programming of a
model. If you switch the transmitter off with the RF
module switched off, next time you switch the trans-
mitter on it will be switched back on again.
Use the arrow buttons  of the left or right-hand
touch-key to move to the “RF module” line, and touch
the central SET button of the right-hand touch-key to
activate the value window:
phase 4 landing
6
receiv out
rx bind
R08
range test
99sec
RF transmit
OFF
Now you can use the right-hand arrow buttons to switch
between OFF and ON. Touch the central SET button of
the right-hand touch-key again to conclude the input.
81


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info