467107
47
Zoom out
Zoom in
Previous page
1/200
Next page
47
Updating the receiver firmware
When you have called up the program, you will see
the number “1” flashing red in the numeric row 1 … 5
at the top of the window, indicating that the program
is currently operating at “[Process Step] 1”.
In each case the meaning of the currently flashing
step is indicated immediately below the numeric row:
For example, at Step 1: “Connect USB lead to HoTT
receiver” and “Press File Browse button and select
Update file”, as shown here.
Note:
At any time you can call up an explanation of any
step in the form of Quick-Info by positioning the
mouse pointer over a number.
If you have not already done so, connect your receiv-
er to the PC or laptop at this point. Now click on the
button marked “File Browse” and select the firmware
update file matching your receiver in the “Open file”
dialogue which now appears; the file suffix will be
“bin”.
In the case of the zip file “HoTT_Software_VX” which
you have already downloaded and unpacked, this
will usually be found in the folder whose name starts
with the Order Number of the receiver to be up-
dated. If your receiver is the GR-16 which is sup-
plied in the set as standard, this would be the folder
“33508_8CH_RX”. The file appears in the associated
window. At the same time the “2” starts to flash red:
Note:
The firmware files are encoded in a manner specific
to each product, i.e. if you accidentally select a file
which does not match the product (e.g. transmitter
update file instead of receiver update file), the pop-up
window “Product code error” appears, and you will be
unable to continue the update process.
Follow the instructions for “[Process Step] 2”. With
the receiver still switched off, click on the “Download
Start” button in the “HoTT Receiver Upgrade” window.
(The display changes to “[Process Step] 3”.) Wait un-
til the progress bar starts to advance; this may take
several seconds, depending on your computer.
Only at this point should you switch the receiver on
with the SET button pressed in. After a few seconds
“Line 3” appears in the column “No” of the Status dis-
play, with the message: “Found target device …”. Re-
lease the button at this point. The actual firmware
update process now starts automatically: “11, Start
Firmware upgrade…”.
If the device is not detected, a pop-up window ap-
pears with the message “Target device ID not found”.
If this should happen, check your update arrange-
ments and try again:
In the Status display the progress of the firmware up-
date is indicated by the progress bar.
During the update process the green and the red
LED on the receiver glows a constant green and red.
You must not interrupt the connection between
the transmitter and the PC during the update
process!
The update is finished when the progress bar reach-
es the right-hand end, and the message “12, Com-
plete !!” appears in the bottom line of the Status dis-
play. At the same time the [Process Steps] display
moves on to “5”.
When the update is completed, the green LED goes
out, and the red LED starts to flash.
If the process terminates before the 100% mark is
47


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info