467107
28
Zoom out
Zoom in
Previous page
1/200
Next page
28
Description of transmitter
Boot Download
Success!!!
Please Wait....
… this display:
Firmware
Downloading...
Progress 023/123
The loading process is complete when the counter to
the left of “/” reaches “Data quantity” to the right of it, and
this message appears:
Firmware Upgrade
success!!!
After a few seconds the message disappears, and the
transmitter re-starts. The system is now ready for use
again.
Notes:
If this warning message appears …•
SD-CARD
INSERT
OK
… then there is no memory card in the card slot, or
the card cannot be read.
If the Select window is empty …•
FILE LIST
… then the transmitter cannot find a suitable
firmware file on the SD card in the slot. If this should
happen, check the contents of the “Firmware” folder
on the SD card by inserting it into a PC or laptop.
STICK CALIBRATION
HIDDEN MODE
STICK CALI.
FIRMWARE UPDATE
VOICE
If you suspect that the centre point of your self-centring
sticks (transmitter controls 1 … 4) does not correspond
exactly to 0% travel of the transmitter control, you can
check and - if necessary - correct it using the following
procedure:
Move to the “Model select menu and set up a free
model memory, as described on page 66. It makes no
difference whether you select a fixed-wing or helicopter
model type.
Wait for the usual on-screen messages which appear
in the base display after switching models, then move
to the “Servo display” menu with, for example, a simul-
taneous brief press of the  buttons of the left-hand
touch-key, but WITHOUT moving the trims, or carrying
out any other programming procedures.
If all four of your primary stick functions are still set to
self-centring action, the screen display should look like
this:
1
3
5
7
2
4
6
8
0%
0%
0%
0%
0%
0%
0%
0%
Otherwise the bar and % figure for the non self-centring
stick function - usually that of the throttle / brake or
throttle / collective pitch stick “Ch 1” - will correspond to
the stick’s current position. For example, if the throttle /
brake stick is at the “quarter-throttle” position, then the
screen will look like this:
1
3
5
7
2
4
6
8
0%
0%
0%
50%
0%
0%
0%
0%
Now move each of the two primary sticks to each of the
four possible end-points in turn, but without exerting
pressure at the end-points. At each of the end-points -
eight in total - the screen should show exactly -100% or
+100%, depending on the side of centre. For example,
if transmitter control 2 is at its right-hand end-point, and
the three other stick functions are all at centre, then your
28


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info