637252

Graupner MICRO MAGIC 2014 Manual

6
Zoom out
Zoom in
Previous page
1/15
Next page
GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
#0057088
Keine Haftung für Druckfehler. Technische Änderungen vorbehalten! No liability for printing errors. We reserve the right to introduce
modifications. Sous réserve de modifications! Nous ne sommes pas responsables d’éventuelles erreurs d’impression! 11/2006
22
at the marked points, then form the slot by running
a sharp knife between the two holes, working as
accurately as you can. The slot should only be
trimmed to final size when the deck and hull have
finally been joined.
• The deck can now be glued to the hull: the first step
is to check that the two parts are a snug fit
together; if not, trim them carefully until they are an
accurate fit. Apply UHU plus (e.g. Order No. 962) to
the bow reinforcement (part 9) and the central
girder (part 25) where the parts meet. Now apply
plenty of UHU plast spezial to the edge of the deck
- omitting the stern area - and join the parts without
delay. IMPORTANT: ensure that neither the hull
nor the deck is distorted when the parts are joined.
Hold the hull and deck together using adhesive
tape or rubber bands while the glue is hardening.
However, don’t apply too much pressure, or the hull
will distort. Allow the glue to cure completely, then
apply a little UHU plast spezial along the joint
edges to fill any lurking gaps.
• Apply plenty of high-viscosity (thick) cyano-acrylate
glue to the unglued gap at the stern. TIP: move the
parts relative to each other to persuade the
adhesive to work its way into the joint. Tape the
stern area together while the cyano is hardening.
• The stern area can now be sanded flat;
alternatively you can leave the hull projecting
slightly beyond the deck.
• At this point you must check the hull / deck joint for
leaks. You may need to run more cyano along the
joint to fill any remaining gaps.
• The deck can now be stiffened by gluing the central
bulkhead (part 19) to the keel / mast socket (part
5).
• The rudder bush (part 26) is glued in the hull next;
you may need to trim the hole slightly. Position the
rudder bush in the hull as shown on the plan, and
glue it in place using think cyano, forming a narrow
fillet of adhesive round the bush at top and bottom.
Allow the glue to cure completely, then sand back
the underside flush with the hull. It is important that
the gap between the rudder (part 27) and the
surface of the hull is as small as possible. If the gap
is not even, you may need to trim the top edge of
the rudder blade to match the shape of the hull.
• Set the rudder servo (part 28) to centre from the
transmitter, fit the output arm (part 29) on it, and
install the servo in the servo plate using the
retaining screws provided.
• Assemble the tiller (part 30) from the plastic lever,
the collet and the M3 screw. Fit the tiller assembly
on the rudder shaft and tighten the retaining screw.
• Drill two 2 mm Ø holes for the cable guides (part
31) in the positions shown, cut two 15 mm lengths
from the snake inner sleeve provided, and glue
them in the holes in the hull using cyano.
IMPORTANT: ensure that the guides are angled
correctly, so that the cables have as straight a run
as possible when installed at a later stage.
• Drill two 4 mm Ø holes in the hull for the sheet
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MICRO MAGIC 2014 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MICRO MAGIC 2014 in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info