747992
56
Zoom out
Zoom in
Previous page
1/80
Next page
56 / 80 33028_mc_28_Teil2_jh
Trim X-axis function
This function can be activated by tapping the left-hand t or the right
u selection button of the right-hand touch panel while the value
field is active. You can then move the active point horizontally or ver-
tically using the selection buttons.
Deleting support points
Place the marker frame in the "Point" line and briefly tap the SET but-
ton. The value field displayed is highlighted. Then set the vertical line
through the control of the mixer input to the support point. The sup-
port point number and the corresponding support point value are
displayed in the "Point" line. Now simultaneously tap on the selec-
tion buttons t u or   of the right-hand touch pad. The
selected support point is deleted and the numbering of the remain-
ing support points is updated. The support points "L" and "H" cannot
be deleted.
Rounding off the curve
The angled curve profile can be automatically rounded off simply by
pressing a button. Set the curve value from "off" to "on" (or vice
versa). Close this process by pressing the SET button or the ESC but-
ton.
MIX act. / Phase
In this menu you can phase-specifically deactivate and activate the
"free mixers" of the previously described "free mixers" menu. Switch
to the desired phase and page in this menu with the selection keys.
The mixers of the "free mixers" menu are displayed line by line. If in
the right colum, the respective mixer is set with the selection keys
"--" the mixer is deactivated in the phase displayed in the lower part
of the display. At the same time it is dimmed in the menu "free
mixer".
Only mix channel
In this menu, the direct control/servo connection can be separated
depending on the phase. If a channel is set to "only mix", this chan-
nel can only be used for one mixer. The channel can no longer be
used for the output. This applies only to the phase that is currently
active. In the "normal" position, the control signal of the channel
acts on the mixer and on the output.
+35%
–37%
Input
Output
Point 2
C.Mix 9
normal
Kurve aus
810
–55%
Trim X axis
0%
–12%
Input
Output
Point ?
C.Mix 9
normal
Curve
810
0%
on
LinearM1
LinearM2
LinearM3
6EL
C1 EL
LinearM4
3 8
SEL
yes
SEL
yes
yes
yes
Mix act. in phase
normal
MIX-only channel
only
normal
1 2 3 456
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC26 in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC26

Graupner MC26 User Manual - German - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info