747992
55
Zoom out
Zoom in
Previous page
1/80
Next page
55 / 80
33028_mc_28_Teil2_jh
Offset (mixer neutral point)
The dotted vertical line in the middle of the graphic indicates the
position of the mixer neutral point ("offset"). This is the point on the
control travel where the mixer does not affect the control channel.
By default this point is in the control center.
If you select the line under "Offset", the bottom line will show "STO"
and "SET".
Define the position for the offset with the control by selecting “STO”.
Select "SET" and the value is entered using the selection keys.
Setting the curve mixer C9 - C12
Open the display page in the column " ". Mixer guide lines can be
defined for the four curve mixers. These guide lines can be defined
by up to four freely adjustable points between the two endpoints "L"
(low = -100% control travel) and "H" (high = +100% control travel). In
the default settings of the program, 2 support points are already
defined, the endpoints "L" and "H".
Setting support points
Move the control of the mixer input to obtain a vertical line in the
graphic to the right of the display. This line shows the position of
the control. Move the line to the point to the desired support
point. Tap the SET button. A 1 and a percent display appear in the
"Point" line. If necessary, add the further three points.
Support points moving
Move the vertical line with the control of the mixer input to the sup-
port point "L, 1 to 4 or H". The support points will be changed. The
number and the current curve value of this point are displayed.
Activate the value field of the line Point. Then use the selection keys
to change the value to between -125% and +125%.
Trim point function
Alternatively, if the value field is active, select already set points by
ascending or descending with the selection keys. The selected point
is marked in the graphic with a triangle. The selected support point
can then be changed with the selection keys. Tap the ESC button to
exit this trimming function.
Trim offset function
If the value field is active, you can select and change already set ver-
tices by ascending or descending with the selection keys. You can
move an existing curve vertically with the  keys in the range of ±
25%.
Tap the ESC button to exit this trim offset function.
–45%
0%
0%
Input
Output
Point ?
C.Mix 9
normal
Curve off
810
+35%
–55%
Input
Output
Point 2
C.Mix 9
normal
Curve off
810
–55%
–35%
+55%
Input
Output
Point 2
C.Mix 9
normal
Kurve aus
810
–55%
Trim point
+35%
–80%
Input
Output
Point 2
C.Mix 9
normal
Kurve aus
810
–80%
Trim offset
55


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC26 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC26 in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC26

Graupner MC26 User Manual - German - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info