30121

Graupner MC18 Manual

19
Zoom out
Zoom in
Previous page
1/56
Next page
Code 58 Mode 32 Code 18
Model Type Model Name Engine Idle Trim
Selection of Model Type Entering Model Names Idle Trim Direction Forward/Backward/Off
19
m
c
-
1
8
E
M
O
D
E
L
1
N
O
R
M
A
L
/
D
I
F
F
The PROFI-ULTRASOFT-Module recognises a total
of 9 different model types. The selection has to be
performed when beginning to program a model, as it
determines which codes may be called. A code
number which is incompatible with the model type
concerned, will be rejected by a message “INH
(WRONG TYPE)”.
The following model types can be selected via
buttons 1 ... 9 on activation of code 58, with the
selected type indicated in the lower line of the display.
Key Display Meaning
1 NORMAL Conventional model
2 NORMAL/DIFF Same as 1, but with 2 aileron servos
and differential
3 DELTA/DIFF Deltas and flying wings with
aileron/elevator mix
4 UNIFLY/DIFF Models with plain flaps operated by a
single channel
5 QUADRO-FLAP Same as 4, but flaps operated by 2
channels
6 F3B (3 wing sv) F3B model with 3 wing-mounted
servos (1 channel for flaps)
7 F3B (4 wing sv) F3B model with 4 wing-mounted
servos (2 channels for flaps)
8 Heli Universal helicopter program including
models with RPM control
9 Heli (sp.ctl) Helicopter with RPM control only
When changing model type via code 58, you must be
aware of the fact that some of the already
programmed adjustments will be deleted and reset to
their basic values, even if immediately switched back
to the initial model type.
N
A
M
E
:
D
I
S
C
U
S
3
3
0
Due to the variety of model programs which can be
stored in the transmitter at the same time, it will not
be easy to remember the number of a model, the data
of which have been stored in memory. For this reason
the name of a model can be additionally stored. The
relevant test, which must not exceed 11 symbols, is
indicated in the multi-data terminals display.
On selecting code 32 the earlier input text will appear
or, when programming for the first time, an empty
line. Using the INC and DEC keys the letters of the
alphabet and numbers 0 through 9 may be selected.
Use of the TURN key permits switching from capital
letters to lowercase. When the desired character
appears it is accepted by pressing STORE and the
next character can be selected. When finished, press
the ENTER key.
Deletion of data input is performed by pressing the
CLEAR key.
If analogue input is used, via a proportional rotary
module connected to the AUX socket, for selection of
the characters, special symbols will be available in
additional to capital letters and numbers, for dressing
up a names.
m
c
-
1
8
E
M
O
D
E
L
1
I
D
L
E
R
.
T
R
I
M
Idle trim is permanently allocated to control function 1
(throttle) and permits precision adjustments of idle
RPM to be performed without affecting full throttle
adjustments.
Code 18 enables the pilot to adapt idle trim to the
direction of operation of the throttle stick he uses.
After calling the code, the direction of operation (push
or pull) can be reversed by pressing the INC and
DEC keys. The currently active adjustment is shown
on the display in a stylised control stick which
indicates idle stick position.
Idle trim can be switched to normal trim – bi-
directional effect – by pressing the CLEAR key.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC18 in the language / languages: English as an attachment in your email.

The manual is 7,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC18

Graupner MC18 User Manual - German - 188 pages

Graupner MC18 User Manual - French - 58 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info