30117
80
Zoom out
Zoom in
Previous page
1/104
Next page
Free Programmable Mixer
(access via Set-Up Menu)
80 Helicopter
Freely Programmable
Mixer
Additional to the pre-programmed mixer functions
contained in the helicopter program are two freely
selectable mixers, which are characterized by the
letters A and B and the number of the input function
and the output channel. The lower display line will
show either the mix portion and direction, or "OF" if
the mixer is switched off using the associated
external switch.
Setting example for mixer "A"
1. Channel Selection
.
Firstly the CH SEL button is pressed until in the
upper display line "Ach" appears. Using the INC key
the number of the input channel 1 to 8 is entered (left
digit), with the DEC key the channel of the receiver
output 1 to 8 (right digit). Pressing the CLEAR button
performs a reset and sets input function and output
channel to "1", mix proportion and offset to 0% and
the mixer switch on "ON".
2. Allocation of a mixer switch
.
Pressing the CH SEL button changes the display to
"ASW" (A-Switch). This is where it is specified
whether the mixer remains constantly switched on,
(display "ON" is shown), or whether it is turned on
and off by an assigned external switch. The selection
is made with the INC or DEC keys. The lower line
of the display shows the transmitter board socket for
the external switch allocated:
Mixer Transmitter Socket
A 7
B 6
Note
:
Switch 6 also simultaneously switches the mixers for
static and dynamic torque compensation, and switch
7 the automatic gyro gain reduction.
3. Setting mix proportion and mix direction
.
By pressing the CH SEL button the option for
adjusting the mix proportion and direction appears.
Using the INC and/or DEC buttons the mix
proportion can be set between 0 and ±125%,
symmetrically to the neutral point (pressing CLEAR
resets the value to 0%). If an external switch was
assigned, the mixer can be switched off now and the
display will show "OF".
4. Specify the mixer neutral point (offset setting)
.
If CH SEL is pressed again, you arrives at the offset
setting. To set the offset place the control stick in the
desired position and press the CLEAR key. The
offset is indicated in the display. (value range:
approx. -85 to +85).
If an external switch has been assigned and is
switched off, the display shows "OF".
(If you want to change the stored offset, the mixer
offset setting is re-entered and the new position
stored as above).
Thus the programming of mixer A is completed. The
setting of mixer B is completed in the same way.
Note
:
In the helicopter programs control function 6 cannot
be used as input signal for a mixer as it does not
possess an “output point for mixers” (see the block
diagram on page 62). The signal from this channel
only affects receiver output 6 directly and servo
travel is limited to 25% of the normal value.
Dependent on the type of swashplate (Swash Mixer)
certain control paths are linked with one another (as
with all finished mixers). For example, the basic
standard mixer "N" links control function 1 with
channel 6. The mix proportions of a finished and a
freely programmable mixer can be overlaid in such a
way that a servo movement is changed.
80


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC16 in the language / languages: English as an attachment in your email.

The manual is 16,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC16

Graupner MC16 User Manual - German - 68 pages

Graupner MC16 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info