467111
317
Zoom out
Zoom in
Previous page
1/345
Next page
317
Programming examples - Using ight phases
travel +" as well as the offset value and the mixer
proportion set in the "Multi-ap menu" of the »Wing
mixers« menu, see further below.
Leave the (control) "- travel +" at its standard sym-
metric settings of +100 % and the offset value at
0 %. Specifying a symmetric or asymmetric time for
smooth switching between the three switch posi-
tions – in the example "1.0 s 1.0 s" – in the column
"- time +" is recommended:
0% +100%I5
I6
I7
I8
Ty p
+100%
0.0 0.0
– travel + –time+
0% +100%
+100%
0% +100%
+100%
0.0 0.0
0% +100%
+100%
0.0 0.0
GL
GL Cn1
fr
---
---
---
offset
GL fr
Normal
PH
---
SEL
Sl1 1.0 1.0
In the "Multi-flap menu" of the …
»Wing mixers« (beginning page 160)
… menu, subsequently change only the values for
"FL.pos" and "FL" in the «Thermal» flight phase:
FL.pos
It is here that AI and FL positioning takes place
during the «Thermal» flight phase in the event that
the assigned control (proportional control or 3-way
switch) is in its neutral or middle position.
FL.pos
Diff.
Ail-tr.
AI
Thermal AI
+100%
WK2
FL
0%
+66% 0%
+100%+100%
–9%
+100%
+33%
0%
+33%0%
+100% +66% 0%
0%
FL +100%
0% +100%
–11%
FL
Enter in this line the share of influence for aileron
and camber flap servos, when used as camber
flaps, is to be produced by the selected control
(see above) or 3-way switch. Be sure to set these
values low enough that the flaps can be controlled
with appropriate sensitivity, for example:
Fl.pos
Diff.
AiI-tr.
AI
Thermal AI
+100%
WK2
FL
0%
+66% 0%
+100%+100%
–9%
+100%
+33%
0%
+33%0%
+100% +66% 0%
0%
FL +20% +25%
–11%
+25%
+20%
A simultaneous tap on the  or  key com-
bination of the right touch pad (CLEAR) will reset
changed values back to their standard default values.
Note:
Due to the improved lift distribution, the
degree of mix ratios should be set so that the
camber aps are slightly "lower" than the
ailerons.
With a simultaneous tap on the  keys of the left
touch pad, the reaction of the AI and FL servos can
be checked in the »Servo display« by actuation of
the selected camber flap control. (Push the C1 stick
to the front position so that the "AI" and "FL" posi-
tions can be better followed on actuation of the cor-
responding control.)
Caution:
With aileron actuation the bars of
the »Servo display« move in the
same manner, for camber flap
actuation they will move in the opposite
manner.
In the control's middle position, the example's
"FL-pos." setting only has a -9 % effect for the AI
and -11 % for the FL.
In one transmitter control end-position, AI and FL
are again closer to the neutral position because
the mix ratio specified in the example reduces the
FL.pos setting, whereas …
… in the other limit position, AIL and FL reach
the maximum downward offset prescribed by the
mixer percentage.
In order to set a corrective admix for the eleva-
tor, exit the "Multi-flap menu" and return to the base
screen of the »Wing mixers« menu:
Brake settings
Aileron +50%
WING MIXERS
Flaps aileron +5%+5%
–––
–––
rudder
2
64
3
Thermal
Multi-flap menu
In the two limit positions of the three-stage switch the
elevator is moved symmetrically in this example with
+5 % (true to side). If, on the other hand, you use a
proportional control, the elevator is deflected accord-
ing to the degree for the control position.
Then make the settings for the "Speed" flight phase in
the same manner.
Notes:
The digital trimming of transverse, altitude
and side work independently of these
settings depending on the setting
selected in the»Stick mode« menu, page
114 "global" or for each "phase".
All setting values are model-dependent. Carry out
the settings on your nished model and/or during
the ight.
317


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info