467111
282
Zoom out
Zoom in
Previous page
1/345
Next page
282 Program description - Servo display
Servo display
Display of the servo position
Use the selection keys on the left or right touch pad
to scroll to the menu option »Servo display« menu
option in the multi-function menu:
Teacher / pupil Tx. output swap
Profi trim Trim memory
Telemetry Channel sequence
Multichannel Ring limiter
Mp3 player Basic settings
Servo display Servo test
Briefly tap the centre SET key of the right touch pad
to open this menu option.
1
3
5
7
9
11
13
15
0
0
0
0
–100
0
0
0
–100
0
0
0
+100
0
0
0
2
4
6
8
10
12
14
16
However, the visual display of current servo positions
can not only be opened by selecting this menu, but
also directly from the transmitter's base screen as
well as nearly all other menu positions with a simul-
taneous tap on the  keys of the left touch pad. A
brief tap on the centre ESC key of the left touch pad
will cause a return to the respective point from which
it was called.
The current position of each servo is displayed in a
bar diagram between -150 % and +150 % of normal
travel with consideration for the control and servo set-
tings, the dual-rate/expo functions, the interplay of all
active linear and curve mixers, etc. 0 % corresponds
precisely to the servo centre position. This way, you
can quickly check your settings without having to
switch on the receiver. However, this does not absolve
you from first carefully testing all program steps, as
well as on the model, prior to the first operation of the
model in order to eliminate errors!
For winged models the display takes place
according to the following scheme:
Bar 1 = Throttle/brake servo
Bar 2 = Aileron or left aileron
Bar 3 = Elevator
Bar 4 = Rudder
Bar 5 = Right aileron
Bar 6 = Camber-changing flap (left) / free
channel
Bar 7 = Right camber-changing flap / free
channel
Bar 8 = Free channel / second elevator servo
Bar 9 = Free channel / Left FL2
Bar 10 = Free channel / Right FL2
Bar 11 = Free channel / Left AI2
Bar 12 = Free channel / Right AI2
Bar 13 = Free channel
Bar 14 = Free channel
Bar 15 = Free channel
Bar 16 = Free channel
… and for helicopter models:
Bar 1 = Pitch or roll (2) or pitch (2) servo
Bar 2 = Roll (1) servo
Bar 3 = Nick (1) servo
Bar 4 = Tail servo (gyro)
Bar 5 = Nick (2) servo / free channel
Bar 6 = Throttle servo or speed controller
Bar 7 = Gyro sensitivity / free channel
Bar 8 = Speed controller / free channel
Bar 9 = Free channel
Bar 10 = Free channel
Bar 11 = Free channel
Bar 12 = Free channel
Bar 13 = Free channel
Bar 14 = Free channel
Bar 15 = Free channel
Bar 16 = Free channel
Notes:
However, please note that the servo
display is only based on the original
sequence of servos. This means that any
swapping of outputs which may have been
implemented, in either the »Transmitter
output« menu or »Receiver output« menu, is
not taken into account.
Please also note that, by default, bar diagram
tracking is opposite to the left/right movements of
a stick.
The number of channels shown in this menu
correspond to the 16 control channels available
in the mc-32 HoTT transmitter. However, the
number of actually usable channels depends
on the receiver type as well as the number of
servos connected to it and, therefore, may be
considerably lower under certain circumstances.
Use this display during the model programming,
because you can immediately check all settings
on the transmitter. However, this does not absolve
you from rst carefully testing all program steps,
as well as on the model, prior to the rst operation
of the model in order to eliminate errors!
282


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info