467111
266
Zoom out
Zoom in
Previous page
1/345
Next page
266 Program description - Multichannel
–––
SEL Offset
Input 1
Input 2
Input 3
Input 4
fr
fr
fr
–––
–––
–––
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
0%
0%
0%
0%
– travel +
fr
MULTICH 2
Now the desired transmitter control can be selected
with the selection keys on the left or right touch pad.
If the selected control has an assignment, it can be
disconnected from a transmitter control switching its
field to "fr".:
transmitter control 1 … 4 (CH 1 …4)
slider control 1 … 3 in the middle of the console
(Sl1 … 3)
depressible, roller-shaped proportional speed
control (Tv1 … 5)
side proportional control (Lv1 and Lv2)
(Function inputs "UV1" through "UV8", which are also
in the selection list, can be selected at a later time
and then connected as necessary.)
Note:
If you are using the Nautic-Expert switch
module, No. 4159, any proportional controls
you assign act like switches when close to
their end-points.
"Switch"
Select by the use of the selection buttons the line
over the switch symbol .
This column is used to assign each of the inputs
used, 1 through 8 (maximum), to any switch available
on the transmitter. These assignments are done as
described in the section “Assigning transmitter con-
trols, switches and control switches” on page 60:
–––
Offset
Input 1
Input 2
Input 3
Input 4
fr
fr
fr
–––
–––
–––
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
0%
0%
0%
0%
– travel +
3
MULTICH 2
Move desired switch
to ON position
(ext. switch: SET)
Any controls which were previously assigned in the
second column will be erased. In this case, instead of
SEL, the switch symbol will be displayed at the
bottom of the 2nd column such that now a second
“normal” switch, or even a transmitter control switch,
logical switch, … can be assigned as needed from
the group of “expanded switches”. In general it is suf-
ficient to assign a simple switch or transmitter control.
–––
Offset
Input 1
Input 2
Input 3
Input 4
fr
fr
fr
–––
–––
–––
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
0%
0%
0%
0%
– travel +
3
MULTICH 2
Erasing transmitter controls or switches
With transmitter control / switch assignment active,
simultaneously pressing the  or  buttons of
the right-hand four-way button (CLEAR) – see screen-
shots above resets the corresponding input to “fr”
and “---”.
Column 2, "Control"
–––
SEL Offset
Input 1
Input 2
Input 3
Input 4
fr
fr
fr
–––
–––
–––
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
0%
0%
0%
0%
– travel+
fr
MULTICH 2
Use the arrow keys to move to the column over SEL.
After completing the activation of transmitter control
assignment by tapping the centre SET key of the right
touch pad, the message shown below will appear in
the display:
–––
SEL Offset
Input 1
Input 2
Input 3
Input 4
fr
fr
fr
–––
–––
–––
+100%
+100%
+100%
+100%
+100%
+100%
+100%
+100%
0%
0%
0%
0%
– travel +
fr
MULTICH 2
Move desired
control adj.
Alternatively, the centre SET key of the right touch
pad can be tapped for a second time while this mes-
sage is on display:
266


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info