467111
262
Zoom out
Zoom in
Previous page
1/345
Next page
262 Program description - Channel sequencer
Channel sequencer
Programming the motion sequences of up to 3 servos
Use the selection keys on the left or right touch pad
to scroll to the »Channel sequence« menu option in
the multi-function menu:
Wing mixers Free mixers
MIX active/phase MIX-only channel
Dual mixer Fail-safe adjust
Teacher / pupil Tx. output swap
Profi trim Trim memory
Telemetry Channel sequence
Free mixers MIX active/phase
MIX-only channel Dual mixer
Swashplate mixer Fail-safe adjust
Teacher / pupil Tx. output swap
Profi trim Trim memory
Telemetry Channel sequence
Tap briefly on the centre SET key of the right touch
pad to open this menu option:
CHANNEL SEQUENCER
Channel
Channel
INACT
INACT
SET
Channel
channel
INACT
14
15
16
The »Channel sequence« menu option can be used
to execute up to 9 exactly coordinated steps for up to
three servos over a period of up to 30 seconds. Such a
sequence can be triggered by a single switch and be-
gin at an initial servo position which is freely adjustable.
For example, this makes the opening of undercarriage
doors, complete with subsequent extension of the
retractable gear, just as simple to program as opening
a wheel well with renewed closing of one undercar-
riage door once the landing gear has been lowered or
to program the raising of a cockpit canopy with subse-
quent head turns and waving performed by the pilot.
However, the prerequisite for all these actions is the
"parsing" of the desired motion sequence into practi-
cal, individual steps.
Programming procedure
On this menu option's first display page, see figure
below left, either accept the three preset channels,
14 … 16, or select an available channel, 5 … 16, for
each line to form any other desired combination, e. g.:
CHANNEL SEQUENCER
Channel
Channel
INACT
INACT
SET
Channel
channel
INACT
10
11
12
With a simultaneous tap on the  or  selection
keys of the right touch pad (CLEAR), the given chan-
nel is reset back to 5, 6 or 7.
The next step makes the control channels needed for
the channel sequence available. This is done in the
"SET" column by changing settings from "INACT" to
"ACT" and thus making the individual channels "avail-
able" to the program for sequencing. Conversely, this
also means that channels defined as "active" in the
»Channel sequence« menu are not available for
other purposes.
“Sensors”
These lines only appear, according to the firmware
version, if you have already activated at least one
sensor in the “SELECT SENSOR” sub-menu of the
»Telemetry« menu; see page 258. The method of
selecting corresponding voice messages is as de-
scribed in the previous sections.
Note:
The points you select here are entirely
independent of the “VARIO” messages.
262


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info