Manual Graupner MC 32 HOTT (page 88 of 345) (English)

467111

Zoom out

Zoom in

1/345

88 Program description - Base setup models | Winged models

• You would like to control the rudder of a large

model with two or more servos.

Assign each of the appropriate outputs (servo

connections) to one and the same input (control

channel). In this case, the default rudder channel

(4), see  gure bottom right.

Notes:

• The maximum number of lines (outputs)

available corresponds to the maximum

number of servos which can be connected

to the receiver in question.

• If you see the warning …

CAN‘T

RECEIVE

DATA

… then there is no bound receiver within range.

If the case may be, switch the RF module or/and

your receiving system on.

• With the »Tx. output swap« option, available

on the mc-32 transmitter, see page 234, the

transmitter’s control functions can be interchanged

in any way; it is also possible to assign multiple

outputs to one and the same control function. In

the interests of clarity however we strongly advise

that you use only one of these two options.

Channel assignment on other receivers

As already mentioned, the "Rcv Ch map" menu op-

tion can be used to freely distribute the mc-32

HoTT transmitter's 16 control channels across up

to four receivers, whereby the numbering of outputs

(servo connections) as well as the maximum num-

ber of available lines (outputs) will correspond to the

maximum number of servo connections available on

the given receiver.

RECEIVER CHANNEL MAP BIND2

Rx Input Ch 16

Rx Output Ch 1

Rx Output Ch 2

Rx Output Ch 3

Rx Output Ch 4

After selection of the desired output with the selection

keys of the left or right touch pad, the respective input

ﬁ eld will be framed. Tap the centre SET key of the

right touch pad. The current setting will be displayed

in inverse video. Now select the desired input chan-

nel with the selection keys of the right touch pad. For

example, suitable to the above rudder example.

RECEIVER CHANNEL MAP BIND2

Rx Input Ch 4

Rx Output Ch 1

Rx Output Ch 2

Rx Output Ch 3

Rx Output Ch 4

Note:

The number of lines available in the list

(outputs) corresponds to the maximum

number of servos which can be attached to

the given receiver.

RF transmit

This menu line provides an option for manually

switching the transmitter's RF transmission on and

off to speciﬁ c models while the transmitter is in op-

eration. For example, to save power while a model is

being programmed.

If this line option was set to OFF, it will be

canceled (i. e. set to ON) the next time the

transmitter is switched on.

If necessary, use the  selection keys of the left

or right touch pad to move into the "RF transmit" line

then activate the option with a brief tap on the centre

SET button of the right touch pad.

Stick mode

Module

bind

bind n/a

n/a

HoTT

SET SET SEL SET

Rcv Ch Map R16 R08 n/a

n/a

RF transmit on

BASIC SETTING,MODEL

The right selection keys can now be used to choose

between OFF and ON. Another tap on the centre SET

key of the right touch pad will conclude the entry.

Range test

Note:

This menu line is when “EXT. PPM “in the

line” module hidden “.

The built-in range test reduces transmission power

to an extent that a functional test can be carried out

even within a distance of less than 100 m.

Perform a range test on the Graupner HoTT system ac-

cording to the following instructions. If necessary, have

someone assist you in carrying out the range test.

1. Preferably, the receiver already bound to the

transmitter should be installed into the model in its

intended position.

2. Switch remote control on and wait for the green

LED to light up on the receiver/s. Now servo

movements can be observed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MC 32 HOTT Manual

Product: