Manual Graupner MC 32 HOTT (page 85 of 345) (English)

467111

Zoom out

Zoom in

1/345

Program description - Base setup models | Winged models

On the other hand, should the LED on the receiver

blink red for longer than about 10 seconds, the

binding process has failed. In this case the screen

will continue to show the status as "n/a". If this

should happen, try changing the position of anten-

nas then repeat the entire procedure.

• Receiver GR-12L

At the receiver, the red LED lights. Press and hold

the SET button on the receiver until the red LED

goes out after about 3 seconds for a further 3 sec-

onds. You can now release the SET button on the

receiver. As long as the LED is off, the receiver is

in bind mode. Start now-as described above-within

these 3 s to bind the receiver to the current model

memory. If the LED of the receiver is still dark and

the display in the transmitter changes to “b”, the

binding process has been completed success-

fully. However, the red LED will light up red again

at the receiver, the binding process has failed.

At the same time appear in the line “module” of

the display again “n / a”. If necessary, change the

positions of the antennas involved and repeat the

entire procedure.

Binding other receivers

The binding channel you have chosen is already

bound (as indicated by the "bind" status). This bind-

ing is to be replaced by another. After initiating the RF

bind process, instead of displaying "BINDING", the

message shown below appears.

Model name

Stick mode 1

geb.

BASIC SETTING,MODEL

Info

n/a

Module geb.

HoTT

Graubele

1234g/111111

SEL BD1 BD2 BD3 BD4

off

is turned

Drop down two lines in the screen and switch off the

RF module as described on the page in section "RF

module". Afterward, return again to the "Module" line

and restart the binding process as described above.

Alternatively, the transmitter can be switched off

brieﬂ y then, after switching it back on again, respond

to the message window that appears …

OFFON

Please select

RF on/off?

… with "OFF" …

Please select

RF on/off?

OFF

… then conﬁ rm the selection with a brief tap on the

centre SET key of the right touch pad. From the base

screen jump again into the "Module" line of the »Ba-

sic settings, model« menu and restart the binding

process.

Dissolving a bond

Proceed as described above to initiate the binding

process but WITHOUT ﬁ rst putting a receiver in bind-

ing readiness.

EXT. (PPM signal at DSC sock-

et)

If your transmitter is ﬁ tted with a non-Graupner exter-

nal RF module connected to the DSC / Data socket,

you can switch between the standard internal HoTT

RF module and the external module when you switch

model memories in the “Module” line by choosing

either “HoTT”, “EXT.”, or “SP.”, as described in the fol-

lowing section.

You can now use the arrow button  of the right-hand

four-way button to move to the ﬁ rst Value ﬁ eld in the

“Module” line before pressing the central SET button

of the right-hand four-way button:

Model name

Stick mode 1

BASIC SETTING,MODEL

Info

Module

Graubele

1234g/111111

SEL

HoTT

BD1 BD2 BD3 BD4

bind bind n/a n/a

In the active Value ﬁ eld you should now use the Se-

lect buttons to choose “EXT.” or – if appropriate – the

“SP.” mode (described below) instead of “HoTT”.

When you select “EXT.”, the HoTT-speciﬁ c value ﬁ elds

are replaced by the modulation type already selected

in the “DSC output” line; see page 89:

Model name

Stick mode 1

BASIC SETTING,MODEL

Info

Module

Graubele

1234g/111111

SEL

PPM10

EXT. PPM

The lines of the “Receiver output” and “Range test”

options (described below) are also suppressed, as

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MC 32 HOTT Manual

Product: