747993
72
Zoom out
Zoom in
Previous page
1/80
Next page
72 / 80 33028_mc_28_Teil2_jh
5. Phase assignation menu:
Switch off the autorotation switch
Select the switch for the normal flight phase and switch it off in
the correct position.
Select combination C and press the SET key
Run the selected flight phase switch.
Switch to test whether the switch between the flight phase Nor-
mal and Acro 3D is correct.
6. Helicopter mixer menu:
Activate the autorotation switch
Throttle position AR -100% for electric motor, -90% for IC engine.
Deactivate the autorotation switch.
Select CH1->Throttle
Pre-programmed diagonal throttle curve can be used for com-
bustion engines and electric motors with controllers without
Govenor mode. Pitch stick = Throttle stick
For speed controllers with Govenor mode a horizontal gas line
must be programmed as follows:
In the "lower" normal flight phase, select a lower throttle / speed
than in the second Acro 3D flight phase, e.g. 40%. Move the pitch
stick to min. and tap the SET button. With the up arrow, the
beginning of the curve can now be set to e.g. 40%. Deselect this
point of the curve with the SET key and set the pitch stick to max.
Tap the SET button again and lower the rear point to 40% to cre-
ate a horizontal throttle line. Deselect with the SET button.
Now use the flight phase switch to switch to Acro 3D. As described
above, program a higher throttle line / speed , e.g. 65% throttle.
Afterwards you have now programmed 3 speeds / flight phases
for the Govenor:
Autorotation for motor off
Normal flight phase with 40% throttle
Acro 3D flight phase with 65% throttle
If a flybarless system is used in which the control travel needs to
be calibrated, seting up this flybarless system before setting the
throttle curves is advantageous. The preprogrammed diagonal
throttle curve of channel 6 can be calibrated more easily.
Phase assignment
A B C D E F
265
1 Normal
prior
combi
Phase settings
Non-delayed chan
Announce
Timer (general)
Phase timers
Phase assignment
C1
C1
Pitch
Throttle
Tail
Tail 0%
Roll 0%
Throttle
Roll
Throttle
Tail
Nick
Nick
Throttle
Tail
Swash rotation
Swash limiter
0%
0%
0%
OFF
Normal
Gyro suppress 0%
Gyro gain 0%
SEL
Free mixers
MIX active/phase
Phase timers
Helicopter mixer
MIX-only channel
Swashplate mixer
Input
Output
Point ?
0%
0%
0%
Pitch
Normal
Curve off
+50%
+50%
+50%
C1 Throttle
Input
Output
Point
Normal
Curve off
?
72


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info