747993
39
Zoom out
Zoom in
Previous page
1/80
Next page
39 / 80
33028_mc_28_Teil2_jh
Note
The trim of "Elevator", "Aileron" and "Rudder" is factory-set to
"Global". This setting can be changed at any time to "phase-specific"
in the "Sticks setting" menu.
Channels without delay
In this menu, you can switch off the switching delay set in the "Phase
setting" menu for individual control channels that are dependent on
the phase.
Switch to the corresponding phase (this is shown in the lower left
corner of the display).
Set the desired channel through the selection keys.
Use the SET button to change the channel (normal / reverse)
Timers (general)
The model timer, battery timer, Timer up and Timer middle are set
here.
Model time
This timer shows the currently recorded used time of the active
model memory. To switch the time recording manually, assign a
switch in the right column.
The buttons t u or  of the right touch-pad reset the timer
to "0:00h".
Batt time
This timer shows the use time of the battery. The timer will be reset
as soon as the battery is fully charged. The time is added at each use
of the transmitter.
The buttons t u or  of the right touch-pad reset the timer
to "0:00h".
Timer up and middle
These two timers are located in the upper right half of the basic dis-
play. A different name can be assigned. The function and use mode
depend on the name. Regardless of the name, the "up" and "middle"
timer can be programmed backwards or forwards as a "timer".
Stop/motor
These two timers will start and stop with a switch, in the column "
". Move the marking frame with the selection key over the
"Timer" column to the right side to reach the column.
Phase settings
Phase trim
Annnounce
Timers (general)
Phase assignment
Non-delayed chan
Non-delayed channels
non-delay
normal
Normal
7 8 9 10 11 12
Non-delayed chan
Timers (general)
Phase timers
Wing mixers
Free mixers
MIX active/phase
Model time
Batt. time
Top:
Centr:
Stop
Log t.
Timer
–––12:34h
1:23h
0:00
0:00
39


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC-28 4D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC-28 4D in the language / languages: English as an attachment in your email.

The manual is 17,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info