747933
40
Zoom out
Zoom in
Previous page
1/51
Next page
40 / 52
S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh
Swp cyclic travel 8
Set the "Swp cyclic travel 8" if the menu value is acvated so that the
rotor blade located above the tail tube is as accurate as by full roll-
over stroke. To do this, the field must be selected (highlighted field)
so that the swashplate can be controlled and adjusted in direct mode
when gyro gain is switched o. This is the only mode in which the
travel can be set correctly.
It is very important that the travel is set correctly. It plays a major role
in terms of acquiring the correct gyro gain.
Collecve_A/B
The display "A" or "B" and its corresponding value changes automat-
ically according to the transmier-side pitch sck posion. The two
endpoints are set separately.
Use the pitch gauge to measure the required pitch travel
when the
full commands are applied (±100%) and set it in this menu. All of the
other sengs can be made later on the transmier for the pitch
curves in the respecve flying phase.
Adjustment range: +50 … +120
Cyclic max
The swashplate limit must be set so that it is not possible for a servo
to reach its mechanical limits, while ensuring that the servo's travel
is as large as possible. No humming should come from any of the ser-
vos when full travel commands are applied.
Adjustment range: +50 … +200
Swp rotate
In this line, a virtual swashplate rotaon can be set in degrees.
Normally for rotor heads with up to a 3 bladed no rotaon is neces-
sary.
Adjustment range: ±90
Tail servo
In this line the correct neutral posion for the tail servo has to be set.
As a rule, 1.5 ms are not just usual for tail servos. Narrowband ser-
vos (generally special
tail rotor servos) may however require a dier-
ent mid pulse width. You must locate this value in the servo manual
and set it correctly. If a value has not been specified, it is probably a
standard servo set at 1.5 ms. For Graupner servos of type DES, HVS
or HBS, this value is parally programmable. However, we recom-
mend scking with the default seng.
Base sett control
Swp direction +0
Swp Roll trim +0
Swp Nick trim +0
Swp cyc. trav 8 +80
Direction right
Swp type 120 degree
Swp Pitch trim +0
Swp frequency 200Hz
Collective A +80
Cyclic max. +80
Swp rotate +0
Tail servo 1,5ms
Tail frequency 333Hz
Tail mid +0
Tail limit B +50
4.Swp servo mid +0
Logging +3
Expert mode NO
40


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-24 PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-24 PRO in the language / languages: English as an attachment in your email.

The manual is 8,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner GR-24 PRO

Graupner GR-24 PRO User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info