747934
29
Zoom out
Zoom in
Previous page
1/36
Next page
29 / 36
S1035_Falcon_12_jh_V1
If you want to use the An-ballooning compensaon, start with the
value "30". A reducon of the parameter eg to the value "25"
increases the "rearing" tendency. An increase to, for example, "35"
reduces the tendency but can also adversely aect the final speed.
You need to find an opmal compromise between safe flight behav-
ior without rearing and maximum speed. For this, rst start in 5 steps
and then make the fine tuning in 1 steps.
Tail rotor seng without Expertmode
Tail sensivity
1-100, min or C5…C16
Default seng: 65
The "Tail sensiv." row allows you to specify a sensivity seng
either using the values 1 to 100 or by assigning a channel (C5 to C16)
with a proporonal control, which is used to control the value.
The max. tail sensivity is rst determined at the highest speed and
it should be own individually for each speed. It can be increased
unl the tail begins to swing up. Aerwards, the tail sensivity has
to be reduced a lile, unl in all flight posions no swinging of the
tail is recognizable anymore.
Dierent sengs can then be used through the HoTT transmiers
to adjust the sensivity based on specific flight phases, eg through
the control sengs or the "Gyro" in the hely mix menu.
Tail rate
50 -120, default seng: 85
Sets the max. potenal rate of rotaon in Rate mode for the tail.
Tail Expo
0 -50, default seng: 40
You can set here an exponenal curve (0 - 50%) for the rate of the
tail. Low percentages result in a linear increase in the rate of rota-
on. High percentages produce a strong curve, the heli then no lon-
ger reacts so sensive to the center of the sck. The Expo seng can
also be adjusted in a phase-related manner at the transmier. But
avoid a overlapping of GR18 Expo and transmier Expo.
 
 
  
  
Servo travel
Servo travel
Servo travel
Control travel
Control travel
Control travel
Expo = +100%
Expo = +50%
Expo = –100%
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner FALCON 12 - S1035 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner FALCON 12 - S1035 in the language / languages: English as an attachment in your email.

The manual is 12,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner FALCON 12 - S1035

Graupner FALCON 12 - S1035 User Manual - German - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info