637239
10
Zoom out
Zoom in
Previous page
1/16
Next page
10
GR-18_Copter_jh_V1
Step 3
Axis assignment in the gyro
sequence this parameter has to gas curve, will be explained
in next section.
MINPOWER %
The setting is principally used to prevent the motors shut
down in flight. Adjust so that the motors are running straight.
Under no circumstances unnecessarily high set, this would
limit the controller possibilities. These are some internal chan-
nel 1 curves:
Mode = normal: (Attitude+Rate) <-95%: Motors off, from
about minimum gas linear increase
Note: When in use with mode = normal we suggest, to pro-
gram a switch in the transmitter, which can set channel 1 at
least at -95%, so that while fling you cannot stop completely
the motors.
LOGGING
Value 1 is the general attitude control, rest as needed logs the
corresponding servo to SD card for later evaluation and error
analysis.
Settable values:
0 = No logging, Telemetry display of Euler and yaw angle
1 = Roll and Nick logging
We suggest to set at least one function.
CALIBR. POSITION
With Calibr. Position the acceleration sensors can be calibrated
so that in attitude mode with stick and trim neutral, the copter
is precisely horizontally aligned. For this purpose, it is simply
placed on absolute level surface and set the value to Yes. Af-
ter a moment, it jumps back to No and the calibration is done.
Do not forget to store disabling the field!
Axis assignment
Setup: Setup: Yes/No
Assignment of the gyros and their operating direction.
In the receiver’s “Axis assign” menu, go to the “Setup” option
and set it to “Setup: Yes”. Now assign the axes as follow:
Ð On the transmitter, briefly set the roll command fully to the
right; the roll axis is highlighted. Roll the Copter more than
45 degrees to the right
the identified axis with the
required prefix is displayed, the field is no longer highlighted
and identification of this axis is complete.
Ð Now do the same for nick: on the transmitter, briefly set the
nick command so that it is fully forward. Roll the Copter
more than 45 degrees forwards; the axis is displayed, the
field is no longer highlighted and identification of this axis
is complete.
Ð Finally complete the procedure for the yaw: on the
Axis assignment <
>Setup No
ROLL +0
NICK +0
YAW +0
10


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner 33579 - GR-18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner 33579 - GR-18 in the language / languages: English as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner 33579 - GR-18

Graupner 33579 - GR-18 User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info