637239
7
Zoom out
Zoom in
Previous page
1/16
Next page
INNOVATION & TECHNOLOGIE
7
GR-18_Copter_jh_V1
Connections
Connect the speed controllers or Servos to the row of sock-
ets on one end of the receiver. The connectors are polarised:
note the small
chamfers on one side. Never use force - the connectors should
engage easily. The polarity is also printed on the receiver; the
negative wire (-) is brown, the positive (+) red and the signal
orange. The servo sockets of Graupner HoTT 2.4 receivers are
numbered sequentially. The socket for channel 8 (K6 in GR
18) can also be programmed to deliver a (digital) sum signal
(see next section).
Power supply
The receiver does not feature specific sockets for connect-
ing the battery. We recommend that you connect the power
supply to the socket(s) close to the servos already connected
to the receiver. If you wish to connect multiple separate bat-
teries, the batteries must be of the same nominal voltage and
capacity. Never connect batteries of different type, or packs
of greatly differing states of charge, as this can cause effects
similar to a short-circuit. If you encounter this problem, we
recommend the use of a voltage stabiliser unit (e.g. PRX-5A
receiver power supply, Order No. 4136) between the batteries
and the receiver.
Telemetry or channel (T/9) socket
The optional telemetry sensors are connected to the socket
marked “T” (T/9)- Telemetry. In addition, the update is per-
formed on this socket (see point 5). The socket can be used
optionally for K9. (see next section)
Receiver setting menu
The receiver set-up menu appears in the “Telemetry” menu
under SETTINGS / DISPLAYS; alternatively - if you are using a
SMART-BOX - under SETTING & DATAVIEW. The method of
accessing this menu is described in the operating instructions
supplied with your transmitter or the Smart-Box.
Low-voltage warning (ALARM VOLT)
If the receiver voltage falls below the set value, a low-voltage
warning is generated by the transmitter’s RF module in the
form of the “general alarm tone”: a regular beeping at a rate of
about one per second; alternatively the speech output mes-
sage “Receiver voltage”.
Temperature warning (ALARM TEMP)
If the receiver temperature exceeds the set temperature thresh-
old, a warning is generated by the transmitter’s RF module in
the form of the “general alarm tone”: a regular beeping at a
rate of about one per second; alternatively the speech output
message “Receiver temperature”.
OK
RECEIVER Q.01 >
>ALARM VOLT: 3,8V
ALARM TEMP: 70°C
max altitude: 25m
>PERIOD: 20ms
>SUMD at CH6: No
Sensor at CH9: No
LANGUAGE: english
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner 33579 - GR-18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner 33579 - GR-18 in the language / languages: English as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner 33579 - GR-18

Graupner 33579 - GR-18 User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info