637239
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
GR-18_Copter_jh_V1
Ð Protect the receiver from dust, dirt, moisture and other for-
eign parts. Do not expose this equipment to vibration and
excessive heat or cold. The remote control operation may
be carried out only in “normal” ambient temperatures, in a
range from -10 ° C to +55 ° C.
Ð Use all of your Hott components only with the latest Soft-
ware version
Ð If any questions arise that can not be ascertained with the
help of the operating manual, please contact us (contact
information, see page 3) or another expert.
WARNING
Pay attention, even while programming, that the connected
motors do not start suddenly. Injury risk by the turning pro-
pellers!
Avoid shock and pressure. Check the receiver regularly for
damages to the housings and cables after every flight. Dam-
aged or wet electronic components, even if re-dried, should
no longer be used.
Installation in the model (Copter)
The receiver must be placed in line with one side of the Cop-
ter, secure it to the receiver holder. The lower surface of the
receiver must always be parallel to one of the copter sides.
Put some double-sided tape on the bottom of the receiver
and use the optimal double taped pads S8376 for Gr-18,
S8377 for Gr-24 PRO.
Binding
The binding is only possible if the receiver has not yet been
binded to another transmitter (red LED blinks). Pushing the
SET button the receiver will be set in Bind mode.
If you want to bind an already binded receiver to another
memory, follow the next steps:
Ð Turn off the RF module in the “Basic setting“ menu (see
transmitter’s manual)
Ð Switch on the receiver pushing the SET button to bring it in
bind mode
Ð Start the binding in the “Basic setting“ menu
Ð If within 10 seconds the red light turns off and the green
LED will light, the binding process was successful.
Ð Your RC system is now ready for use.
Ð If the red LED is still on it means that the binding process
didn’t work properly. In this case repeat the procedure.
!
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner 33579 - GR-18 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner 33579 - GR-18 in the language / languages: English as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner 33579 - GR-18

Graupner 33579 - GR-18 User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info