68471
33
Zoom out
Zoom in
Previous page
1/39
Next page
Grandstream Networks, Inc. GXP User Manual Page 33 of 39
Firmware 1.1.6.46 Last Updated: 03/2008
Use DNS SRV:
Default is No. If set to “Yes”, the client will use DNS SRV to look up server.
User ID is Phone
Number
If the phone has an assigned PSTN telephone number, this field should be set to
“Yes”. Otherwise, set it to “No”. If “Yes” is set, a “user=phone” parameter will be
attached to the “From” header in SIP request
SIP Registration
This parameter controls sending REGISTER messages to the proxy server. The
default setting is “Yes”.
Un-register on Reboot
Default is No. If set to “Yes”, the SIP user’s registration information will be
cleared on reboot.
Register Expiration
This parameter allows user to specify the time frequency (in minutes) that GXP
refreshes its registration with the specified registrar. The default interval is 60
minutes. The maximum interval is 65,535 minutes (about 45 days).
Local SIP Port
This parameter defines the local SIP port used to listen and transmit. The default
value for Account 1 is 5060. It is 5062, 5064, 5066 for Account 2, Account 3 and
Account 4 respectively.
SIP Registration Failure
Retry Wait Time
Retry registration if the process failed. Default is 20 seconds.
SIP T1 Timeout
RFC 3261 SIP T1 timer. Default is 1 second.
SIP T2 Interval
RFC 3261 SIP T2 timer. Default is 0.5 seconds.
SIP Transport
Choose SIP Transport between UDP and TCP. Default is UDP.
Use RFC3581
Symmetric Routing
Default No. When selected the phone will follow the routing procedures specified
in RFC3581.
NAT Traversal (STUN)
This parameter activates the NAT traversal mechanism. If activated (by choosing
“Yes”) and a STUN server is also specified, the phone performs according to the
STUN client specification. Using this mode, the embedded STUN client detects if
and what type of NAT/Firewall configuration is used. If the detected NAT is a Full
Cone, Restricted Cone, or a Port-Restricted Cone, the phone will use its mapped
public IP address and port in all of its SIP and SDP messages. If the NAT
Traversal field is set to “Yes” with no specified STUN server, the GXP will
periodically (every 20 seconds or so) send a blank UDP packet (with no payload
data) to the SIP server to keep the “hole” on the NAT open.
Subscribe for MWI:
Default is No. When set to “Yes” a SUBSCRIBE for Message Waiting Indication
will be sent periodically.
PUBLISH for Presence
Enable Presence feature.
Proxy-Require
SIP Extension to notify SIP server that the unit is behind the NAT/Firewall.
Voice Mail UserID
When configured, user can access messages by pressing “MSG” button. This ID
is usually the VM portal access number.
Send DTMF
This parameter specifies the mechanism to transmit DTMF digit. There are 3
supported modes: in audio which means DTMF is combined in audio signal (not
very reliable with low-bit-rate codec), via RTP (RFC2833), or via SIP INFO.
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grandstream GXP-1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grandstream GXP-1200 in the language / languages: English as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info