68471
31
Zoom out
Zoom in
Previous page
1/39
Next page
Grandstream Networks, Inc. GXP User Manual Page 31 of 39
Firmware 1.1.6.46 Last Updated: 03/2008
Call Progress
Tones
Using these settings, users can configure ring or tone frequencies based on parameters
from local telecom. By default, they are set to North American standard.
Frequencies should be configured with known values to avoid uncomfortable high pitch
sounds.
Syntax: f1=val,f2=val[,c=on1/off1[-on2/off2[-on3/off3]]];
(Frequencies are in Hz and cadence on and off are in 10ms)
ON is the period of ringing (“On time” in ‘ms’) while OFF is the period of silence. In order
to set a continuous ring, OFF should be zero. Otherwise it will ring ON ms and a pause
of OFF ms and then repeat the pattern. Up to three cadences are supported.
Intercom User
ID:
This field is used to configure the Intercom key in the phone. For GXP2010 and
GXP2020 only
If the phone is working with a GS GXE502X IP-PBX it can be configured in the following
manner:
To page an extension : [intercom feature code]+[*]+[extension number]
To page a group : [paging group feature code]+[*]+[group extension]
Disable Call
Waiting
Default is No. If set to Yes, the call waiting feature will be disabled.
Disable Call
Waiting Tone
Default is No. If set to Yes, the call waiting tone will be disabled.
Disable Direct
IP Calls
Default is No. If set to Yes, direct IP calls will be disabled
Use Quick IP
Call Mode
Dial an IP address under the same LAN/VPN segment by entering the last octet in the IP
address.
In the Advanced Settings page there is an option “Use Quick IP-call mode”. Default
setting is No. When set to YES, and #XXX is dialed, where X is 0-9 and XXX <=255,
phone will make direct IP call to aaa.bbb.ccc.XXX where aaa.bbb.ccc comes from the
local IP address REGARDLESS of subnet mask.
#XX or #X are also valid so leading 0 is not required (but OK). See Quick IP Call Mode
for details.
Disable
Conference
Default is No. If set to Yes, conference will be disabled.
Lock keypad
update
If set to “Yes”, the configuration changes via keypad are disabled.
Enable MPK
Sending DTMF
Default is No. If set to “Yes”, Muti-Purpose keys can be sent as DTMF.
For GXP2020/2010/2000.
Disable DND
Default is No. If set to “Yes”, the “DND” button on keypad will be disabled. For GXP2000,
MUTE/DEL button functions as DND button when pressed while phone is idle.
Disable
Transfer
Default is No. If set to Yes, transfer will be disabled.
Display CID
instead of Name
If set to “Yes”, CID will be displayed in the screen instead of Name. Default is ”No”. For
GXP280 only.
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grandstream GXP-1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grandstream GXP-1200 in the language / languages: English as an attachment in your email.

The manual is 0,78 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info