768365
8
Zoom out
Zoom in
Previous page
1/49
Next page
ENEN
14 15
For a bigger baby, use the lower
harness loop 2.
 Thread the shoulder harness
straps through the head support
slot to fasten the head support
to the straps, and then pull the
adjustment webbing tight.
 Reassemble the webbing cover to
the body.
 Route the Vehicle Safety Belt
Pull out the vehicle safety belt,
rotate the child restraint forward
and thread the belt through the
two forward-facing vehicle waist
belt slots at the back of the child
restraint shell.
 Buckle the vehicle safety belt.
 Open the lock-o device and
insert the vehicle shoulder belt
through it. Close the lock-o
device onto the vehicle shoulder
belt.
Please check if child restraint is
installed tightly by moving the
child restraint back and forth at
the vehicle belt path.
(Child restraint should not move
more than 25mm/1”).
 While pressing the child restraint
rmly into the vehicle seat, pull
the vehicle shoulder belt toward
the retractor to fasten the child
restraint tightly and securely.
The child restraint cannot be
used if the vehicle safety belt
buckle (female buckle end) is too
long to anchor the child restraint
securely.
 Correctly Assembled Vehicle
Belt
Ensure vehicle shoulder belt
passes through Lock-o Device
A
Ensure vehicle waist belt passes
through the forward-facing
vehicle waist belt slots B
Ensure that the vehicle buckle
tongue is engaged with the
buckle correctly C
 Loosen Harness Straps
While pulling up on the webbing
adjuster, pull out the shoulder
harness straps to proper length.
 Unbuckle the buckle and then
place harness straps o to the
sides.
 Place Your Child in the Seat
Place Harness Straps Over
Child’s Shoulders And Buckle
Harness Straps
Make sure their back is at
against the car seat back.
You will hear a click” when buckle
tongues are securely attached.
Pull up on each buckle tongue to
make sure it is securely attached.
 Tighten Harness Straps
Pull down on the adjustment
webbing to adjust the tment
around child. Ensure adjusted
properly to keep child secure,
removing any slack in the
harness.
 Be Sure the Harness Straps are
at the Proper Height
Rear-Facing: The shoulder
harness slots should be at
or slightly below the child’s
shoulder. Shoulder harness straps
that are too high or too low are
not safe.
Forward-Facing: The shoulder
harness strap slots should be
at or slightly above the child’s
shoulder. Shoulder harness straps
that are too high or too low are
not safe.
 Infant Insert
Infant insert is for child’s
protection. It must be used for
children 0-6 months. Continued
use of insert above 6 months, is
permitted rearwards facing only,
for additional support.
 Infant Body Support
Remove the head support
portion of the infant insert when
the child’s head no longer ts
comfortably.
Remove the body support
of the infant insert when the
infant’s shoulders no longer t
comfortably.
 Foam Insert
To remove, pull out the foam
insert out. Remove the foam
insert to allow more space
when the infant does not t
comfortably.
 DO NOT install this child
restraint on vehicle seats that
face sideward or rearward with
respect to the moving direction
of the vehicle.
 Do not place this child restraint in
seating positions where an active
frontal airbag is installed If your
child is still in rear-facing mode.
 DO NOT create a gap between
vehicle seat and TOP of child
restraint. A
DO NOT hang over front of
vehicle seat. B
If child will not keep the vehicle
seat belt properly positioned, DO
NOT use this child restraint, use a
dierent car seat.
 Identify Your Vehicle Safety Belt
Type
This child restraint is only suitable
for vehicle seats with 3 point
retractor safety-belt.
 Remove the webbing cover from
the body.
 At the back of the seat,
disassemble the two shoulder
harnesses from the T-shaped steel
plate.
 Pull out the shoulder harness
straps.
 Thread the shoulder harness
covers through the shoulder
harness strap slots.
 Unbuckle the buckle and then
place harness straps o to the
sides.
 Remove the fastening pieces on
sides of the seat pad from the two
slots on both sides of the body.
 Remove the fastening pieces in
front of the seat pad from the two
slots on the bottom of the body.
 Thread the adjustment webbing
and harnesses on both sides out
from the seat pad.
To remove the crotch strap cover,
rst locate the elastic on the
inside of the crotch strap cover.
Pull both the elastic and the
crotch strap cover over the buckle
to remove.
 Thread the buckle out from
seat pad slot for crotch strap to
remove the seat pad.
To clean the soft goods, please
refer to the washing label on the
child restraint.
 To assemble soft goods in reverse
steps.
 Store instruction manual in the
slot with the instruction book
icon as shown.
Replacement Parts
To purchase parts or accessories,
please contact us at the
following:
gracobaby.eu
www.gracobaby.pl
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graco Extend at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graco Extend in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info