Manual Graco Endure (page 7 of 25) (English, German, French, Italian, Spanish)

768363

Zoom out

Zoom in

1/25

1211

Now you can strap your child into the seat. Make sure the

seat belt has not become twisted. Also check that the

cover is not impeding the movement or fit of the seat belt

webbing in any way. Ensure rigid and plastic parts of child

restraint are not liable to become trapped by a movable

vehicle seat or vehicle doors.

To release your child restraint follow the above instructions

in reverse order.

Fastening the Harness

Slot the two metal sections of the buckle connectors together.

19 -1

Slot the two buckle connectors into the slot in the top of the

buckle until they “click” into place. 19 -2

Always check the harness is correctly locked by pulling the

shoulder straps upwards.

To release the harness, press the red button on the buckle

downwards.

Tightening the Harness

Pull the shoulder straps upwards to remove the slack from the

lap sections of the harness. 20 -1

Pull chest pads down as far as they can go. 20 -2

Now pull the adjuster strap until the harness is fully tightened.

20 -3

The harness should be adjusted as tightly as possible

without causing discomfort to your child.

Ensure that the lap strap portion of the harness is located as

low as possible towards the thighs-not round the tummy.

A loose harness can be dangerous. Check the harness

adjustment and tighten each time the child is placed in the

seat.

Slackening the Harness

The harness is slackened by pressing the lever (under the seat

cover) on the front of the seat. 21 -1

Grip the two shoulder straps with one hand. Then press down

on the lever underneath the softgoods as you pull the shoulder

straps towards you to loosen the harness. 21 -2

Take care when adjusting the shoulder straps that you do

not trap the harness adjuster straps as you press the lever

down.

TAKE CARE - Check harness straps are not twisted.

15-36 kg

Removing the Safety Harness Shoulder Straps

22 Firstly, loosen the harness.

23 From the rear of the seat find the harness connector. 23 -1

Slide both the harness straps off the harness connector at

the back of the backrest. 23 -2 From the front of the seat,

pull the straps through the slots in the seat backrest and

fabric cover.

Removing the Safety Harness Lap

Straps and Crotch Strap

24 From underneath the seat, locate the three webbing

retainer buckles. Turn the buckles on their narrowest end

and feed them, complete with webbing straps, through the

slots in the base of the seat, then through the slots in the

fabric cover. The lap straps and crotch strap can then be

removed completely from the seat.

Store the newborn liner, chest pads, crotch pads and

harness straps in a safe place.

Adjusting the Headrest

According to the child’s height, the headrest can be adjusted up

or down.

25 Put one hand on the backrest. Pull the button in the

headrest with your other hand. 25 -1

Move the headrest up or down as required ensuring your

child’s head is centred on the headrest. 25 -2

Check to make sure it is clicked into one of the six height

positions by pulling up on head support.

The red seat belt guides must be level with, or just above,

the shoulders, as shown by the dotted line.

26 Using the correct headrest height, as shown in 26 .

Fitting the child restraint using

the Adult Seat Belt

IMPORTANT: Before fitting the seat remove the shoulder

straps, crotch strap and lap strap. (See 22 to 24 )

27 Place the child restraint onto the vehicle’s seat. Ensure that

the backrest of the seat is pushed firmly against the backrest

of the vehicle’s seat. Place the child in the child restraint.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graco Endure in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graco Endure Manual

Product: