Manual Graco Endure (page 6 of 25) (English, German, French, Italian, Spanish)

768363

Zoom out

Zoom in

1/25

109

5. If in doubt, consult either the child restraint manufacturer or

the retailer.

Care and Maintenance

THESE INSTRUCTIONS ARE IMPORTANT. PLEASE READ

CAREFULLY AND RETAIN FOR FUTURE REFERENCE.

It is dangerous to NOT follow the instructions for this product.

Backrest cover removal

First release the elastic strap at the bottom of the backrest cover.

Slide the cover o. The cover can now be cleaned.

Headrest and Seat cushion cover removal

Slide the cover o. The cover can now be cleaned.

Washing the covers

Machine wash cover in cold water on delicate cycle and drip-dry.

DO NOT USE BLEACH.

Assembling your Endure Child Restraint

1 Once removed from the box, place your new Endure on the

floor as shown in 1.

2 Open the two parts out so that the backrest and seat lie flat,

as shown in 2.

3 Locate the two hooks at the base of the backrest over the

bars on the back of the seat base (inset).

Raise the backrest to the vertical poistion until it snaps into

place.

9-18 kg

Using the Correct Shoulder Strap Height

Please always read the manual before using it. The manual is

located in the pocket at the side of the seat.

Using the correct shoulder strap height, as shown in 4.

Using the Correct Strap Positioning

For infants and toddlers (9kg to 18kg) use middle and bottom

slots and the top loops on the harness strap. 5-1

For older children (up to 18kg) use the top and middle slots and

the bottom loops on the harness strap. 5-2

Fitting the Child Restraint with the

3-Point Lap & Diagonal Seat Belt

Position the child restraint on the vehicle’s seat.

14 Thread the diagonal of the vehicle seat belt underneath

the headrest as indicated with the red tag, and the lap strap

between the base of the child restraint and the armrest

of the child restraint as indicated with the red tag. Pull the

vehicle seat belt out as much as it will go so there is lots

of slack and feed in through the seat belt route slot in the

seat’s plastic backrest furthest from the vehicle’s seat belt

buckle as indicated with the red tag.

15 Feed the belt buckle around the back of the child restraint

over the harness straps and back through the opposite seat

belt route slot, to the front of the child restraint.

16 Pull the buckle through the slot and push the child restraint

firmly against the backrest of the vehicle’s seat.

17 Feed the buckle and both the diagonal and lap straps

between the armrest and the base of the child restraint as

indicated with the red tag.

18 Fasten the vehicle seat belt into the seat belt buckle making

sure the vehicle seat belt and the buckle are in line with

each other. Please contact the child restraint manufacturer if

in doubt about this point. Finish tightening the vehicle seat

belt until there is no slack and the seat is held firmly in place.

Changing the Shoulder Strap Height

6 Firstly, loosen the harness.

7 From the rear of the seat find the harness connector. 7-1

Release the strap from the harness connector. 7-2

8 From the front of the seat, pull the strap through the slot in

the seat’s backrest and chest pad.

9 Thread the chest pad through to the back.

10 Thread the chest pad back through the next slot up or

down on the cover and backrest, depending on the size of

your child.

11 Pull the chest pad through to the front of the seat.

12 Make sure that the rubber side of the chest pad faces the

child’s chest. Thread the harness strap through the chest

pad. Make sure NOT to twist the straps.

13 Re-thread the harness strap back onto the harness

connector at the back of the seat.

Repeat for the other harness strap.

Ensure both straps are at the same height.

Recommended to keep your child harnessed as long as

possible.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graco Endure in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 1,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graco Endure Manual

Product: