590771
48
Zoom out
Zoom in
Previous page
1/160
Next page
48 GMC-I Messtechnik GmbH
R
ISO
Insulation Resistance
Sequence
Safety class I devices
: The protective conductor test must already
have been passed as a prerequisite for the insulation resistance test.
Ð Select the test: R ISO softkey.
Ð Connect the DUT to the test socket, or connect the probe.
Ð Select measuring range, test voltage Ut and measurement du-
ration.
Ð Select the type of connection via measurement type.
Note
All switches at the device under test must be set to the on
position during measurement of insulation resistance, includ-
ing temperature controlled switches and temperature regula-
tors as well. Measurement must be performed in all program
stages for devices equipped with program controllers.
Ð Start the test: Press the ONSTART key.
Ð After each reconnection to the mains, and as soon as the first
test is started, a mains connection test is executed (see
section 4.1.1).
Attention!
!
Testing is conducted with up to 500 V. Current limiting is uti-
lized (I < 10 mA), but if the terminals (L and N) are touched,
electrical shock may occur which could result in conse-
quential accidents.
Note
Open-circuit voltage is always greater than nominal voltage.
Ð
Special case, SC2 connection: Contact exposed conductive parts
with the probe during measurement.
Ð
All measured values are displayed.
Ð
End the test: Press the
ONSTART
key.
Ð
Read the measured value and compare it with the table of
allowable limit values.
Minimum Allowable Limit Values for Insulation Resistance
Notes Concerning Test Standard 0701-0702
If the measured value is less than 0.3 M for safety class I de-
vices which include a heating element, leakage current must be
measured as described on page 52, and this test must be
passed. The same applies to mains powered safety class II elec-
tronic devices if the required value of 2 M is not complied with.
In the case of safety class II devices, all exposed conductive parts
must be contacted with the probe, and insulation resistance must
be measured.
Batteries must be disconnected from their terminals during testing of bat-
tery powered devices.
Test
Standard
Test voltage
R
ISO
SC I SC II SC III Heaters
VDE 0701-
0702 :2008
500 V
1M 2M 0.25 M 0.3 M
IEC 62353
(VDE 0751-1)
2M 7M
70 M 70 M
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt SECUSTAR FM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt SECUSTAR FM in the language / languages: English as an attachment in your email.

The manual is 1,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info