590777

Gossen Metrawatt PROFITEST MXTRA Manual

77
Zoom out
Zoom in
Previous page
1/96
Next page
GMC-I Messtechnik GmbH 77
XR
E
The polarity of the 2-pole adapter must be reversed.
XI
N
/ I
F
N and PE are swapped.
XX
I
N
/ I
F
Z
L-N
/ Z
L-PE
/ R
E
1) Mains connection error
Remedy: Inspect mains connection.
or
2) Display in the connection pictograph: PE interrupted (x) or
underlying protective conductor bar interrupted with reference to the
keys at the test plug
Cause: voltage measuring path interrupted
Result: measurement is disabled
Note: only if appears: Measurement can nevertheless be started by
pressing the start key again.
XI
N
/ I
F
Display at the connection pictograph:
Overlying protective conductor bar interrupted with reference to the keys
at the test plug
Cause: current measuring path interrupted
Result: no measured value display
R
E
I
N
/ I
F
Probe is not detected, probe not connected
Remedy: inspect probe connection
R
E
Clamp is not detected:
– Clamp is not connected or
– Current through clamp is too small (partial earth resistance too high) or
– Transformation ratio set incorrectly
Remedy: Check clamp connection and transformation ratio.
Check the batteries in the METRAFLEX P300 and replace
if necessary.
R
E
If you have changed the transformation ratio at the test instrument, a
message appears prompting you to change the setting at the current
clamp sensor as well.
R
E
Voltage too high at clamp input or signal distorted
The transformation ratio parameter selected at the test instrument might
not correspond to the transformation ratio at the current clamp sensor.
Remedy: Check transformation ratio or setup.
All
Battery voltage is less than or equal to 8 V.
Reliable measurement is no longer possible.
Storage of measured values to memory is disabled.
Remedy: Rechargeable batteries must be recharged, or replaced towards
the end of their service life.
I
N
/ I
F
Resistance in N-PE path is too high.
Consequence: Required test current cannot be generated, measurement
is aborted.
Z
L-PE
, R
E
Upon exceeding the specified contact voltage U
L
:
Z
L-PE
and R
E
: request to switch to the 15 mA wave
only R
E
alternatively:
Request to reduce the measuring range (reduce current)
Status
Test
plug
Meas.
Adapter
Position of the
Function Switch
Function / Meaning
I
N
/I
F
10 mA 30 mA 100 mA 300 mA 500 mA
R
MAX
for I
N
510 170 50 15 9
R
MAX
for I
F
410 140 40 12 7
… 77 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt PROFITEST MXTRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt PROFITEST MXTRA in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt PROFITEST MXTRA

Gossen Metrawatt PROFITEST MXTRA User Manual - Dutch - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info