590777

Gossen Metrawatt PROFITEST MXTRA Manual

35
Zoom out
Zoom in
Previous page
1/96
Next page
GMC-I Messtechnik GmbH 35
10.6 Earthing Resistance Measurement, Mains Powered – Selective Earthing Resistance Measurement with Current Clamp Sensor
as Accessory
As an alternative to the conventional measuring method, measurement can also be performed with a current clamp sensor.
Key
R
B
Operational earth
R
E
Earthing resistance
R
L
Cable resistance
R
X
Earthing resistance through equipotential bonding
systems
R
S
Probe resistance
PAS Equipotential bonding busbar
RE Overall earthing resistance (R
E1
// R
E2
// water pipe)
Measurement without clamp: R
E
= R
E1
// R
E2
Measurement with clamp: R
E
= R
E2
=
Select Measuring Function
Select Operating Mode
Connection
2-pole adapter, clamp and probe are connected.
Set Parameters at Tester
q Measuring range (test current selection):
1 k (40 mA), 100 (0.4 A), 10 (3.7 ... 7 A)
In the case of systems with RCCBs, the DC + functions
can be selected (only in the 10 range and only with the
METRAFLEX P300).
q Connection type: 2-pole adapter + clamp
After parameter selection: automatic setting to 10 measuring
range and 1 V/A or 1000 mV/A transformer ratio
q Contact voltage: UL < 25 V, < 50 V, < 65 V, see section 5.7 re-
garding freely selectable voltage.
q Test current waveshape:
Sinusoidal (full-wave), DC offset and positive half-wave
q System type: TN/TT, IT
q Current clamp sensor transformation ratio: see table below
Set Parameters at Current Clamp Sensor
q Current clamp sensor measuring range: see table below
Selecting a Measuring Range at the Current Clamp Sensor
Important Instructions for Use of the Current Clamp Sensor
• Use only the METRAFLEX P300 or the Z3512A current clamp
sensor for this measurement.
• Read and adhere to the operating instructions for the
METRAFLEX P300 current clamp sensor, as well as the safety
precautions included therein.
•Observe direction of current flow (see arrow on the current
clamp sensor).
•Use the clamp in the permanently connected state. The sensor
may not be moved during measurement.
• The current clamp sensor may only be used at an adequate
distance from powerful extraneous fields.
• Before use, always inspect the electronics housing, the con-
nector cable and the current sensor for damage.
P
R
O
F
I
T
E
S
T
W
a
t
e
r
P
i
p
e
SE
2
E
1
B
U
Probe
I
Clamp
--------------


R
E
Tester METRAFLEX P300 Clamp Tester
Transforma-
tion Ratio
Parameter
Switch Measuring
Range
Measuring
Range
1:1
1 V / A
3 A (1 V/A) 3 A
0.5 ... 100
mA
1:10
100 mV / A
30 A (100 mV/A) 30 A 5 ... 999 mA
1:100
10 mV / A
300 A (10 mV/A) 300 A 0.05 ... 10 A
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt PROFITEST MXTRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt PROFITEST MXTRA in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt PROFITEST MXTRA

Gossen Metrawatt PROFITEST MXTRA User Manual - Dutch - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info