590647
29
Zoom out
Zoom in
Previous page
1/40
Next page
GMC-I Messtechnik GmbH 29
Note
Prior to lengthy periods of rest (e. g. holiday), we recom-
mend removing the (rechargeable) batteries. This helps to
prevent excessive depletion or leakage of batteries,
which, under unfavourable circumstances, may cause
damage to the instrument.
If leakage has occurred, the electrolyte must be carefully and
completely removed with a damp cloth before installing new bat-
teries.
Replacing the Batteries
See section 3.2 and section 12.3.
12.2 Fuses
If a fuse has blown due to overload, a corresponding message
error appears at the LCD panel. The instrument’s voltage measur-
ing ranges are nevertheless still functional.
12.2.1 Fuse Link – FUSE Message
This fuse is active in all resistance measuring ranges except for
voltage measurement. A replacement fuse is included in the bat-
tery compartment (FF315mA/1000V).
Attention!
!
Disconnect the instrument from the measuring circuit be-
fore opening the battery compartment lid in order to re-
place the fuse (refer to page 5 for location)!
Checking the Fuse
If a resistance measuring range is selected with the rotary switch
with a blown or defective fuse in the instrument, and if the instru-
ment is turned on with the switch in this position, fuse appears at
the LCD. Prerequisite: The + and COM measurement jacks are not
short circuited.
After eliminating the cause of error and replacing the defective
fuse, the fuse message is cleared after the instrument has once
again been switched on.
Attention!
!
Severe damage to the instrument may occur if incorrect
fuses are used.
Only original fuses from GMC-I Messtechnik GmbH as-
sure required protection by means of suitable blowing
characteristics.
Short-circuiting of fuse terminals or the repair of fuses is
prohibited!
The instrument may be damaged if fuses with incorrect
ampere ratings, breaking capacities or blowing charac-
teristics are used!
Replacing the Fuse
Ð Open the battery compartment lid by loosening the two
screws.
Ð Remove the defective fuse and insert a new one. A replace-
ment fuse is included in the battery compartment.
Ð Insert the new fuse.
Ð Replace the battery compartment lid and retighten the
screws.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt METRISO TECH at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt METRISO TECH in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt METRISO TECH

Gossen Metrawatt METRISO TECH User Manual - German - 6 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info