590625

Gossen Metrawatt METRAHIT ULTRA BT Manual

28
Zoom out
Zoom in
Previous page
1/74
Next page
28 GMC-I Messtechnik GmbH
V/Hz, Ω, Temperature, and A/Hz Measurements
5 Measurements
5.1 Voltage Measurement
Notes Regarding Voltage Measurement
• The multimeter may only be operated with installed batteries or re-
chargeable batteries. Dangerous voltages are otherwise not indi-
cated, and the instrument may be damaged.
• The multimeter may only be operated by persons who are ca-
pable of recognizing contact hazards and taking the appropriate
safety precautions. Contact hazards exist anywhere, where
voltages of greater than 33 V (RMS) may occur. The test
probes may only be gripped up to the finger guard. Do not
touch the metallic test probes under any circumstances.
• Avoid working alone when taking measurements which involve
touch hazards. Be certain that a second person is present.
• For the METRAHIT ULTRA, maximum allowable voltage between the
connector sockets and ground is 600 V for measuring cate-
gory III and 300 V for measuring category IV.
• Be prepared for the occurrence of unexpected voltages at de-
vices under test (e.g. defective devices). For example, capaci-
tors may be dangerously charged.
• No measurements may be made with this instrument in electri-
cal circuits with corona discharge (high-voltage).
• Special care is required when measurements are made in HF
electrical circuits. Dangerous pulsating voltages may be pres-
ent.
• Be aware of the fact that dangerous voltage spikes are not displayed
during measurement with the low-pass filter. We recommend mea-
suring voltage without the low-pass filter first, in order to be able to
detect any dangerous voltages.
• Be absolutely certain that the measuring ranges are not over-
loaded beyond their allowable capacities. Limit values are included
in section 8, “Technical Data”, in the table entitled “Measuring
Functions and Measuring Ranges” in the “Overload Capacity”
column.
• 300 mV range: Thermovoltages occur in the event of tempera-
ture fluctuation, which appear as additional voltage offset. It
may be necessary to repeat zero offsetting in order to achieve
the specified degree of accuracy.
Scope of Functions, Voltage Measurement
1
A 1 kHz low-pass filter can be used in this case, in order to filter out high
frequency pulses of greater than 1 kHz, for example when performing
measurements at pulsed motor drives.
Function
METRAHIT ULTRA
V AC / Hz TRMS, dB (Ri = 5 MΩ)
1
•
V AC / TP-Filter 1 kHz
1)
(Ri = 5 MΩ) TRMS
•
V AC+DC TRMS / TP-Filter (Ri =5 MΩ)
•
V DC (Ri = 10 MΩ)
•
Pulse frequency, MHz @ 5 V TTL
•
Duty cycle as %
•
Voltage level measurement, dB @ V
AC
@ V
AC+DC
Frequency bandwidth
100 kHz
… 28 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt METRAHIT ULTRA BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt METRAHIT ULTRA BT in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info