330857
4
Zoom out
Zoom in
Previous page
1/17
Next page
Instructions for use, installation and connection
41
Oven illumination
When the oven is on, the lamp is also on, regardless of the
operation mode.
If the oven is off, touch the sensor (1) and select the symbol
"Light" (1), then touch the light ON/OFF sensor (5) turn the
lamp on. Next touch of the ON/OFF sensor turns the lamp
off.
Selection and setting of oven temperature
After selecting the type of food and oven function mode, by
pressing the sensors (3a/3b) you may select the desired oven
temperature in the range from 30 – 250°C (depending upon the
selected operation mode) in 5°C intervals.
During the operation, oven temperature may
be randomly increased or decreased within
the permitted temperature range (see chart)
by pressing the sensors (3a/3b).
Table of data for operation mode (with a sensor 2)
Operation mode
Preset
temperature (°C)
200 160 200 170 250 160 160 150 -
Preset time
(h/min)
---------
Possibillity of max.
set temperature (°C)
250 250 250 250 250 220 220 200 -
Oven thermostat signal lamp (d3-2)
Signal lamp is on; oven temparture is below the setting and
the oven is heating.
Signal lamp is off; the temperature in the oven has reached
the set temperature.
Signal lamp is flashing regularly; the oven is set to the end of
operation mode with the adequate sensor (d4-2); the
preparation of food has not started as yet (the appliance
automatically computes the relevant moment of starting the
oven operation).
Setting the operation time
The time of oven operation may be selected in the range
from 0 to 6 hours, in 1 minute intervals.
After selecting the function mode and the temperature, by
pressing the sensor 4 you may now select the operation time
from 0 to 6 hours, in 1 minute intervals.
Touch the selection sensor (4), the display
(d4-1) starts flashing. By touching sensors (4a/4b) set the
desired operation time.
Turn the oven on with the ON/OFF sensor (5).
When the set time has elapsed, the oven is switched off
(signalled by the beep, oven operation time symbol (d4-1)
and the relevant signal lamp (5a) are flashing).
By touching any sensor (except the ON/OFF sensor (5),
which turns the sound signal off and switches the oven on)
you may switch the sound signal off, otherwise it is turned off
automatically after 7 minutes.
Oven operation time may be changed during
the operation.
Setting the end of operation time
This function is used when you wish to select the end of
operation (cooked food) at exactly the pre-selected time.
The function may be used only with previously set time of
operation ((d4-1) is on).
By touching the selection sensor (4) symbol (d4-2) flashes,
and the display (d4-6) flashes the sum of daily current time
and the oven operation time. Use the sensor (4a) to set the
desired end of oven operation.
Switch the oven on with the ON/OFF sensor (5). The
appliance awaits the start of operation (oven thermostat
signal lamp symbol flashes regularly (d3-2), oven operation
time symbol is on (d4-1) and end of operation time symbol
(d4-2) is also on.
The starting time is now defined automatically. At the
moment the oven starts the operation, the end of operation
symbol (d4-2) goes off, oven illumination is on, and the oven
thermostat signal lamp (d3-2) is on until the set temperature
is reached.
Eventual immediate start of operation may be provoked by
simultaneous pressing of sensors (4a/4b) (for approximately
5 seconds).
Alarm timer
This function may be applied separately, and is not in
connection with the oven operation. It is use whenever you
wish to be warned at a pre-selected time.
By touching the selection sensor (4) provoke flashing of the
alarm timer symbol (d4-4) (the display (d4-6) flashes
"»00:00«). Set the desired time with sensors (4a/4b) in the
range from 0 to 99 minutes in 1 minute intervals. The
countdown starts after approximately 5 seconds, the alarm
timer symbol (d4-4) is on, the display (d4-6) indicates the
current time.
By touching the selection sensor (4) you may check and
correct the remaining time, indicated on the display (d4-6).
By simultaneous pressing of sensors (4a/4b) (approximately
5 seconds) the remaining time may also be set to »00:00«.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje b 9010 e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje b 9010 e in the language / languages: English as an attachment in your email.

The manual is 0,98 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info