656020
6
Zoom out
Zoom in
Previous page
1/14
Next page
1. As a Wireless Studio Flash Trigger
1.1 Mount the transmitter on camera hotshoe and turn it on before
turning on the camera.
1.2 Connect the receiver to studio flash by Sync Cable (one end in
2.5mm Shutter Release Port of the receiver, the other end in
sync port of studio flash) before turning on the studio flash.
1.3 Set the transmitter and the receiver to the same channel.
1.4 Press the camera shutter button, and the studio flash will be
triggered simultaneously. Status Indicator Lamp of both
transmitter and receiver units turn red.
The flash trigger features the following functions:
Using the Flash Trigger
2. As a Wireless Speedlight Trigger
2.1 Mount the transmitter on camera hotshoe and turn it on before
turning on the camera.
2.2 Mount the speedlight to Hot Shoe Speedlight Connection of
receiver unit. Set the speedlight to M mode.
2.3 Set the transmitter and the receiver units to the same channel.
2.4 Press the camera shutter button, and the speedlight will be
triggered simultaneously. Status Indicator Lamp of both
transmitter and receiver units turn red.
3. As a Wireless Shutter Release
3.1 Connect the receiver and the camera by Remote Cable (one
end in receiver’s Shutter Release Port, the other end in
camera’s shutter port) before turning on the camera.
3.2 Half press the <TEST> Trigger Button to focus. When fully
press the <TEST> Trigger Button to shoot, the Status Indicator
Lamp will turn red until releasing the button.
Using the Flash Trigger
4. As a Wireless Studio Flash Trigger or Speedlight Trigger with
PC Sync Socket
4.1 The connection method of the receiver can be found in As a
Wireless Studio Flash Trigger and As a Wireless Speedlight
Trigger section.
4.2 The transmitter will control the flash on the receiver end to fire
via using PC Sync Socket as input by default.
4.3 Press the camera shutter and use the PC Sync Socket’s signal
to control the flash.
4.4 PC Sync Socket can also be set as output. Long press the
<CH/OK> Button of the transmitter until <Fn> is displayed on
the panel. Then, set the value of C.Fn-03 to ou, and the PC
Sync Socket is under output mode.
1. To fire flashes normally, please set the camera flash which
connects to the transmitter or receiver to i-TTL mode.
2. To set ZOOM functions, please open the ZOOM functions on
the camera flash.
3. If high-speed continuous shooting is needed, please set the
groups as required. The shot-to-shot will increase noticeably for
the group that set to TTL mode needs extra preflash time. Turn
off the needless flash groups or set them to M mode to improve
continuous shooting speed.
4. Nikon's CLS system can only control four groups (M/A/B/C). D
and E group cannot be used in TTL mode.
1
2
3
4
- 32 -- 31 -
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox X1N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox X1N in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info