656032
8
Zoom out
Zoom in
Previous page
1/14
Next page
1/4
1/8
1/16
1/32
1/64
1/128
10
2
4
8
20
50
70
20-50
2
4
8
16
30
40
60-100
2
4
8
12
20
40
Hz
Wireless Flash Shooting: Optic Transmission
This product is compatible with Nikon Creative Lighting System
(CLS). It can function as either an optic wireless master or slave
flash. As a master unit, it can control Nikon speedlights e.g. SB-
900 and SB-910 via wireless. As a slave unit, it can be controlled
by wireless signals of Nikon speedlights e.g. SB-900 and pop-up
flash commanders of Nikon cameras e.g. D7100/D7000/D800.
- 39 - - 40 -
Maximum Stroboscopic Flashes:
1/4
1/8
1/16
1/32
1/64
1/128
1
7
14
30
60
90
90
2
6
14
30
60
90
90
3
5
12
30
60
90
90
4
4
10
20
50
80
90
5
4
8
20
50
80
90
6-7
3
6
20
40
70
90
8-9
3
5
10
30
60
80
Flash
output
Hz
Flash
output
You can set up three slave groups for i-TTL autoflash shooting.
With i-TTL autoflash, you can easily create various lighting effects.
Any flash settings for the slave units on the master flash in i-TTL /
Manual / RPT mode will be automatically sent to the slave units.
So the only thing you need to do is to set the master unit for each
slave group without any operation for the slave units at all during
the shooting.
This flash can work in i-TTL / M / RPT / OFF flash modes when set
as a master unit.
Slave/Master Unit's Positioning and Operation Range
Indoors
Outdoors
15m(49.2ft)
10m(32.8ft)
80°
8m(26.2ft) 12m(39.4ft)
Set the flash frequency and
3 flash times.
Press Function Button 3
< > button to select
the item (blinks).
Turn the Select Dial to set
the number and press
Function Button 4 < >
button again to confirm. The
next item to be set will blink.
After you finish the setting,
press <SET> button and all
the settings will be
displayed.
Flash Mode RPT: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture a multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
Press <MODE> button so
1 that < RPT > is displayed.
Turn the Select Dial to choose
2 a desired flash output.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
For example, if the number of flashes is 10 and the firing frequency is
5 Hz, the shutter speed should be at least 2 seconds.
Number of Flashes / Flash Frequency = Shutter Speed
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
Using a tripod and a remote control is recommended.
A flash output of 1/1 and 1/2 cannot be set for stroboscopic
flash.
Stroboscopic flash can be used with“buLb”.
If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
by the following table.
MULTI
Hz
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox V860IIN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox V860IIN in the language / languages: English as an attachment in your email.

The manual is 7,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info