708927

Godox Speedlite Ving V350C Canon Manual

9
Zoom out
Zoom in
Previous page
1/14
Next page
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
Long Press the <SYNC>
1 button for 2 seconds so that
< > is blinking. Turn the
Select Dial until the < > is
displayed on the LCD panel,
which means the slave unit.
Slave Unit Setting
Press the <SLAVE> Button to
1 ch o ose t h e gro u p fro m
M/A/B/C. Then, press the
< MODE > Button so that the
master unit can work in OFF /
TTL / M flash mode. Choose
one of them as the flash
mode of master unit.
3. Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the
channel IDs to prevent signal interference. The channel IDs of the
master unit and the slave unit(s) must be set to the same.
Long press the <SLAVE>
1 Button for 2 seconds until the
channel IDs is blinking. Turn
the Select Dial to choose a
channel ID from 1 to 16.
Press the <SET> button to
2 confirm.
2. Setting Master Unit’s Flash Mode
Press the <MODE> Button for
2 2 seconds to switch to Multi
mode.
Slave Unit Setting
2
● Set the V350C that to be
controlled as the wireless
slave unit. (Page 41)
● The slave unit can be set
as A/B/C.
Check the communication
3 channel
● If the master unit and
slave unit(s) are set to a
different channel, set them
to the same channel.
(Page 41)
Position the camera and
4 flashes
● Position the camera and
flashes as the picture
shows. (Page 43)
Check the flash operation
5
● Press the master unit’s
Test Button< >.
● Then, the slave unit will
fire. If not, adjust the slave
unit’s angle toward the
master unit and distance
from the master unit.
The slave unit might be out of order or fire an unwanted flash
due to the nearby wifi routers or other 2.4G equipments. If in
this case, please adjust the flash’s channel or turn off the 2.4G
equipments.
Autoflash Shooting with One Slave Unit
5. TTL: Fully Automatic Wireless Flash Shooting
Master Unit Setting
1
● Attach a V350C camera
flash on the camera and set it
as the master unit. (Page 40)
● M/A/B/C can be set as
TTL mode independently.
- 41 -
- 42 -
4. Wireless ID Settings
Change the wireless channels and wireless ID to avoid interference
for it can only be triggered after the wireless IDs and channels of the
master unit and the slave unit are set to the same.
Press the <MENU> button to enter C.Fn ID. Press the <SET> button
to choose OFF channel expansion shutdown, and choose any figure
from 01 to 99.
6. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the flash mode to
1 <M>
● Press the <MODE> Button
to set the flash to M mode.
Setting flash output
2
● Turn the Select Dial to set
the flash output of the
groups.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox Speedlite Ving V350C Canon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox Speedlite Ving V350C Canon in the language / languages: English as an attachment in your email.

The manual is 11,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info