656049
4
Zoom out
Zoom in
Previous page
1/5
Next page
When there is flammable accessory on the flash unit, do not keep the
modeling lamp on for a long time. It is recommended to cool it down for one
minute after 10 minutes' working.
Power Output Control
Test Button
Sync Triggering
Slave Trigger Model
Buzz Function
Memory Function
Flash output controller (5) decides different power output, satisfying light requirements
in different environment. The power is adjustable from 5.0 to 8.0 which will be
accordingly shown on the digital display (10). "OF" on the display indicates that the
flash triggering function is shut down. It can automatically discharge power when the
flash output is adjusted from high to low.
To fire the flash without taking a picture, press the test button (9). It can also help
adjust the flash brightness when using together with the flash output controller (5).
The sync cord jack (2) is a Φ6.35mm
plug. Insert a trigger plug here and the
flash will be fired synchronously with
the camera shutter.
Three slave triggering models are
available and can be set by pressing
Slave Model Button (8).
No optical control: The slave triggering indicator (13) is off, indicating the slave
triggering function is shut down.
One fire model: The slave triggering indicator (13) glows blue, indicating the flash
will fire synchronously on one external flash. In this model, the flash can function as an
auxiliary lamp, offering various effects of light and shadow.
Anti-preflash model: The slave triggering indicator (13) glows red, indicating the
flash will receive two external flashes within 2 seconds and will fire synchronously on
the second flash. In this model, the flash can function as an auxiliary lamp, applicable
to TTL system. With this anti-preflash function, synchronization is supported with
cameras having a one-preflash firing system
The sound button (7) is used to decide whether there is sound reminder for ready flash
after recharging. When the buzz indicator (12) is on, the buzz function is working; if it is
off, the buzz function is shut down. A “BI” sound will be heard when it’s fully charged.
The device is equipped with memory function for the panel setting. It will help
remember the panel setting 3 seconds after you set it. When starting up the flash next
time, the panel setting will be the same as that before powering it off.
Wireless Control Function
Tube Replacement
By using the wireless power-control flash trigger, you can wirelessly control the on-
and-off of your flash, modeling lamp and buzzer, as well as adjust the flash output
level. To start this function, insert the trigger receiver into the Wireless Control Port
(20) and make settings on the trigger. You can also press the camera shutter-release
button to trigger the flash by setting the transmitter hotshoe onto the camera hotshoe.
Shut down the power and remove the power cord before replacing the flash tube and
wear insulated gloves. Then, loosen the iron wire on the tube, keep a balanced hold
on the two feet of the flash tube and pull out the old tube gently. Take down the feet
casing from the old tube and put them on the new tube. Hold two feet of the new tube
and target directly towards the two copper outlets, then push them slightly in. Twine
the iron wire on the stainless steel sheet to fix the flash tube.
- 05 - - 06 -
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox Quicker D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox Quicker D in the language / languages: English as an attachment in your email.

The manual is 2,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info