656044
7
Zoom out
Zoom in
Previous page
1/9
Next page
mask
sec
to.1
speed
Multi
CH
S
%
mask
sec
to.1
speed
Multi
CH
S
%
mask
sec
to.1
speed
Multi
CH
S
%
mask
sec
to.1
speed
Multi
CH
S
%
mask
sec
to.1
speed
Multi
CH
S
%
mask
sec
to.1
speed
Multi
CH
S
%
mask
sec
to.1
speed
Multi
CH
S
%
mask
sec
to.1
speed
Multi
CH
S
%
maskmaskmask
secsecsec
to.1to.1to.1
speed
Multi
CH
S
SS
%
maskmaskmask
secsecsec
to.1to.1to.1
speed
Multi
CH
S
SS
%
mask
sec
to.1
speed
Multi
CH
S
%
In this mode, you can set the flash output from 1/128th power to 1/8th power in 0.3 stop increments. With
stroboscopic flash, a rapid series of flashes is fired. It can be used to capture a multiple images of a moving subject
in a single photograph. You can set the firing frequency (number of flashes per sec. expressed as Hz), the number
of flashes, and the flash output.
1/8
1/16(+0.3、+0.7)
1/32(+0.3、+0.7)
1/64(+0.3、+0.7)
1/128(+0.3、+0.7)
1
7
14
30
60
99
2
6
14
30
60
99
3
5
12
30
60
90
4
4
10
20
50
80
5
4
8
20
50
80
6-7
3
6
20
40
70
8-9
3
5
10
30
60
10
2
4
8
20
50
11
2
4
8
20
40
12-14
2
4
8
20
40
15-19
2
4
8
18
35
20-30
2
4
8
16
30
- 25 -
- 26 -
Multi: Stroboscopic Flash
With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
Multi flash mode cannot be set in high-speed sync mode.
With high-speed sync, the color temperature is lower (decrease around 700K) because of tube’s characteristics.
Please set the camera to AWB (Auto White Balance).
Set the flash frequency and flash
3 times.
● Press <SET> Button to select
the flash times. Turn the Select
Dial to set the number.
● Press <SET> Button to select
the flash frequency. Turn the
Select Dial to set the number.
Press <MODE> button so that
1 <Multi> is displayed.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing stops. Use the formula below to calculate the
shutter speed and set it with the camera.
Number of Flashes / Flash Frequency = Shutter Speed
For example, if the number of flashes is 10 and the firing frequency is 5 Hz, the shutter speed should be at least 2
seconds.
Stroboscopic flash is most effective with a highly reflective subject against a dark background.
Using a tripod and a remote control is recommended.
A flash output of 1/1 and 1/2 cannot be set for stroboscopic flash.
If the number of flashes is displayed as “--”, the firing will continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown by the following table.
Maximum Stroboscopic Flashes:
Flash Output
Hz
Turn the Select Dial to choose
2 a desired flash output.
QuickerII adopts built-in 2.4G wireless X system, which is perfectly compatible with other products of our company.
Nikon cameras (using X1T-N, TT685N, etc.) and Canon cameras (using X1T-C, TT685C, etc.) can enjoy one or
more QuickerII together.
*As a slave unit, QuickerII can be controlled by the master unit e.g. AD360II-C, AD360II-N, TT685C, TT685N, X1T-
C, X1T-N, TT600, etc.
Setting the Communication Group
Wireless Flash Shooting: Radio (2.4G) Transmission
Wireless Settings
Press < > Wireless Button so that < > is displayed, entering the 2.4G wireless status now.
Setting the Communication Channel
If there are other wireless flash systems nearby, you can change the channel IDs to prevent
signal interference. The channel IDs of the master unit and the slave unit(s) must be set to the same.
Long press the <GR/CH>
1 Button for 2 seconds until
the channel IDs is blinking.
Turn the Select Dial to choose
2 the channel from 1 to 32.
Press the <SET> Button to confirm.
3
Short press the <GR/CH>
1 Button for 2 seconds until
the group IDs is blinking.
Turn the Select Dial to choose
2 the group from 0 to F.
Press the <SET> Button to confirm.
3
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox Quicker 600 IIM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox Quicker 600 IIM in the language / languages: English as an attachment in your email.

The manual is 5,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info