656045
3
Zoom out
Zoom in
Previous page
1/9
Next page
- 17 -
- 18 -
For Your Safety
Do not disassemble or modify
There are high-voltage components inside the unit. Failure to observe this precaution could result in electric
shock or product malfunction. Should the product break open as the result of a fall or other accident, send the
defective back to authorized service center for inspection and maintenance.
Keep dry
Do not handle with wet hands or immerse in or expose to water or rain. Failure to observe this precaution
could result in fire or electric shock.
Keep out of the reach of children
This device contains small parts that may pose a choking hazard. Consult a physician immediately if a child
swallows any part of this device.
Do not expose to high temperature
Do not leave the device in a closed vehicle under the sun or in other areas subject to extremely high
temperature. Failure to observe this precaution could result in fire or damage to the housing or internal parts.
Before using this product
To prevent damage to the product or injury to you or to others, read the following safety precautions in their entirety
before using this equipment. Keep these safety instructions where users can read them for ready reference.
Caution
After 100 times continuous shots at full power, the flash should be cooled down for about 10 minutes.
Overheating will occur if it is used continuously without cooling down.
Do not keep long time in using the modeling lamp, otherwise the modeling lamp will be deformed, and the
flammable accessories such as softbox will get burnt. The flash can be used continuously at full power for 10
minutes, and then it should be cooled down for one minute.
When using a snoot, do not keep long time the modeling lamp on or over frequent flashlight. Overheating will
result in damages for strobe housing and studio light.
Do not touch the lamp cap when the flash or modeling lamp is working, as it will give out heat, leading to high
surface temperature.
Do not touch the two terminals of the tube outlet as there is high voltage inside. Wear insulated gloves when
replacing the tube or modeling lamp.
Avoid sudden impacts as this can damage the flash tube and/or modeling lamp.
Do not flash directly towards naked eyes (especially those of babies), otherwise it may lead to visual
impairment.
Disconnect from the power supply when it’s not in use.
Conventions used in this Manual
This manual is based on the assumption that both the camera and camera
flash’s power switches are powered on.
Reference page numbers are indicated by “p.**”.
The following alert symbols are used in this manual:
The Caution symbol indicates a warning to prevent shooting problem.
The Note symbol gives supplemental information.
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox Quicker 400 IIM at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox Quicker 400 IIM in the language / languages: English as an attachment in your email.

The manual is 5,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info