636437
16
Zoom out
Zoom in
Previous page
1/27
Next page
15
DiSEqC1.2
a. Move Continuously
Press LEFT/RIGHT button on this item, you
can continuously drive the motor to West
(LEFT) or East (RIGHT). It will stop under
three circumstances: it found signal strong
enough, it meets the limitation you set (see
“Set Limit” for more details), or you release
the LEFT/RIGHT button. If it found signal
and stop, you can adjust the position by
drive the motor step by step (see “Move
Step” for more details) to get best signal
and then store the best position (see “Store
Position” for more details).
b. Move Step
Press LEFT/RIGHT button on this item, you
can drive the motor to West (LEFT) or East
(RIGHT) step by step ( the step is set to 1
by default ).
c. Store Position
Press OK button on this item to store the
current position of the motor for the selected
satellite.
d. Set Limit
Press LEFT/RIGHT button to change
function to “West”(set west limitation),
“East”(set east limitation) or
“Disable”(remove all limitations).
Press OK button to execute the setting.
e. Goto Reference
Press OK button to drive the motor going to
reference position.
After you install your motorized DiSEqC
system well and got signal strong enough,
press RED button to scan it.
USALS
USALS is very convenient motorized DiSEqC
system that supports DiSEqC1.3 command
and also can get the satellite position
automatically if you know your geographical
location. Basically, the listed satellites have its
Longitude and therefore the angle of the
satellite can be calculated without problem. If
you have USALS motorized system, then you
can use the USALS as followings.
a. My Longitude
It means the longitude of your location. You
can set the angle “East” or “West” will be
selected by LEFT/RIGHT button.
b. My Latitude
It means the latitude of your location. You
can set the angle by 0-9 buttons, “South” or
“North” will be selected by LEFT/RIGHT
button.
c. Goto Reference
Press OK button to go to the reference
position.
d. Move
Press OK button to drive the motor to the
exact position corresponding to the satellite
position you are entered.
e. Store
Press OK button to store current position of
the motor for the selected satellite
- Power: Press OK or LEFT/RIGHT button to
set LNB power as OFF, 13, 18, 13/18, 14,
19, 14/19.
Transponder
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Globo OPTICUM 7100CR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Globo OPTICUM 7100CR in the language / languages: English as an attachment in your email.

The manual is 6,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Globo OPTICUM 7100CR

Globo OPTICUM 7100CR User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info